Sewable EL Wire - Easy Sew Tag @ £3.50 per metre

This handy item is a 2.3mm EL wire with sewable tag running along it; it is available in lengths of 50cm, 1m, 3m, 5m and 10 metre.

(EL wire needs a Driver to make it glow - available from £4 in the Inverter/Driver section of the website).

EL Wire twisted into a spiral

The wire is available in any of these colours:

Light Blue (Tron Blue), Purple, Deep Blue, Pink, Red, Orange, Yellow, Lime Green, Turquoise-Green (being discontinued), Grass Green and White

Because the EL naturally glows blue/green the brightest colour of the wire is the Light Blue, Lime Green and White. The least bright are the red and purple as they have to be filtered the most to get the colours right.

The wire has a connector already attached and ready to clip into an EL Driver - THE DRIVER HAS TO BE BOUGHT SEPARATELY

By using splitters you can also connect different strands to the same Driver.

EL wire has loads of uses

It looks amazing when decorating the interior or exterior of cars and motorbikes and can be used inside and outside of your home and office and can even be threaded into clothes and hats.

Our Drivers can run many lengths of EL wire as long as the total length of the wire is under the Driver's maximum capacity

Cutting the wire into the length you choose is simple

1.3mm Fine 'Angel Hair' EL Wire @ £4 per Metre

This 'Angel Hair' EL Wire is a very light diameter of EL Wire, making it a fun and useful material to work with if you're attaching to light fabric.

EL Wire twisted into ringlets

EL Wire twisted into a zig-zag pattern

The colours we stock in this diameter are:
Light Blue (Tron Blue), Deep Blue, Pink, Orangey-Red, Yellow, Lime Green, Turquoise-Green and WhiteWhite

And in these lengths: 10cm / 50cm / 1 metre / 3 metre / 5 metre / 10 metre / 15 metre / 30 metre

This EL Wire comes with a standard connector already attached so simply plugs into any EL inverter - this makes it easy to change between coloured wire on the same Driver.

By using Splitters you can also connect many strands of the glowing wire to the same Driver.

EL wire has loads of uses!

This neon wire looks amazing when decorating the interior or exterior of cars, it can be used inside and outside of the home and office and can even be threaded into clothes and hats.

Our Drivers can run many lengths of wire as long as the total length of the wire is under the Drivers maximum capacity

With some care, the EL wire can be attached to speaker wire to make patterns or extend the neon wire over gaps where it isn't needed.

Joining tape and tubing for re-attaching the wire are available from this store

- this is if you want to cut the EL wire and rejoin it or perhaps attach some wire to a different Driver

Cutting the wire into the length you choose is simple... but rejoining it takes care and attention.

You will definitely need some wire strippers

You can happily use the joining tape and heat shrink tubing for a decent join but if the joint is likely to encounter stress (e.g. if it is threaded into clothes that will then be bent and jostle) or if the join may be hard to reach (e.g. behind a panel in a car) then we would advise soldering to avoid future hassle

There are How-tos and a forum on the site to get some great tips

MAXI EL Wire - 1.5mm High Brightness @ £5 per metre

MAXI EL Wire lives up to its name by bringing together the latest breakthroughs in electroluminescent technology to create a high brightness glowing wire that outshines standard EL Wire.

At 1.5mm in diameter, you will find that whilst making patterns with the MAXI EL Wire, it will hold itself rigid when bent into its desired shape. 1.0mm fine EL Wire also does this, but MAXI EL Wire creates a much more rigid form.

The Maxi EL Wire is more robust than the Ultra EL Wire and is as reliable as the standard EL Wire.

The bend radius of MAXI EL Wire is 5mm; the same as our standard EL Wire.

Breaking strain is at 1kg also the same as our standard EL Wire.

Pressure on the MAXI EL Wire should not be more than 1kg; the same as our standard EL Wire.

These spectacular improvements are due to a thicker copper core giving a greater area of luminosity and helps the EL Wire hold its shape.

MAXI EL Wire uses exactly the same Splitters, Drivers and Sequencers as standard EL Wire.

This remarkable glowing wire is £5 per metre and is available in 50cm, 1 metre, 3 metre, 5 metre, 10 metre and 25 metre lengths (with connectors attached).

It is available in Light Blue, Lime Green, Orange, Yellow, Deep Blue, Deep Pink, Pink and White

Comparing Standard, MAXI and ULTRA EL Wire

As with all electroluminescent technology, because the EL naturally glows blue/green the brightest colour of the wire is the Light Blue, Lime Green and White. The least bright are the red and purple as they have to be filtered the most to get the colours right.

The EL Wire has a connector already attached so is ready to simply clip into an EL Driver - THE DRIVER HAS TO BE BOUGHT SEPARATELY

A wide selection of other EL Tapes, EL Wire, Sequencers, Drivers and helpful EL accessories are available from our store.

2.3mm diameter EL Wire @ £2.50 per metre

The 2.3mm diameter Electroluminescent wire is our cheapest standard EL Wire,

it is available in any of these colours:
Light Blue (Tron Blue), Purple, Deep Blue, Pink, Red, Orange, Yellow, Grass Green, Lime Green, Turquoise-Green and White

300 metre lengths are only available in Lime, Light Blue, Deep Blue, Red and WhiteWhite

2.3mm diameter EL Wire is available in the following lengths:

1 metre, 3 metre, 5 metre, 15 metre, 10 metre, 100 metre and 300 metre

(The 3.2mm diameter wire is also available in 10 metre and 25 metre lengths)

Because the EL naturally glows blue/green the brightest colour of the wire is the Light Blue, Lime Green and White.

The least bright are the red and purple as they have to be filtered the most to get the colours right.

The wire has a connector on it so is ready to clip into an EL Driver - THE DRIVER HAS TO BE BOUGHT SEPARATELY

A wide selection of other EL Tape, EL Wire, Sequencers, Drivers and helpful EL accessories are available from our store

We take custom orders for custom lengths of EL Wire.

This wire comes with a standard connector already attached so simply plugs into any EL Driver.

By using 'Splitters' you can also connect different strands to just one Driver

EL wire has loads of uses!

It has an amazing neon string effect when decorating the interior or exterior of cars and motorbikes and can be used inside and outside of the home and office and can even be threaded into clothes and hats

3.2mm EL Wire @ £3 per metre

The 3.2mm EL Wire is favoured by makers as it is robust and its thickness offers protection while still having a bright neon effect. When placed on a costume or other project it keeps straight lines without showing kinks

It is available in any of these colours:

Light Blue (Tron Blue), Purple, Deep Blue, Pink, Red, Orange, Yellow, Lime Green, Grass Green, Turquoise-Green and White

The wire has a connector on it so is ready to simply clip into an EL driver - THE DRIVER HAS TO BE BOUGHT SEPARATELY

FEEL FREE TO CONTACT US IF WE DO NOT HAVE YOUR REQUIRED LENGTH LISTED

- - - - - - - - - - - -

This wire comes with a standard connector so simply plugs into any EL driver - this makes it easy to change between coloured wire on one driver

By using splitters you can also connect different strands to the same driver

EL wire has loads of uses

It looks amazing when decorating the interior or exterior of cars, can be used inside and outside houses and can even be threaded into clothes and hats

This wire can be cut into smaller lengths and attached to another inverter

Our inverters can run many strips of wire as long as the total length of the wire is under the inverters maximum capacity

With some care, the EL wire can be attached to speaker wire to make patterns or extend the wire over gaps where it isn't needed

Joining tape and tubing for attaching EL Wire is available from this store
this is if you want to cut the EL wire and rejoin it or perhaps attach some wire to a different inverter

Cutting the wire into the length you choose is simple... but rejoining it takes care and attention.

You will also definitely need some wire strippers.

You can happily use the joining tape and heat shrink tubing supplied for a decent join but if the joint is likely to encounter stress (e.g if it is threaded into clothes that will then be bent and jostle) or if the join may be hard to reach (e.g behind a panel in a car) then we would advise soldering to avoid future hassle

It is a cliché to say you are only limited by your imagination but with this neon string it is true!!!

If you have not seen it before it is like a really long glow stick that lasts over 5,000 hours

We're sure you will be amazed - feel free to email or ring us with any questions

Basic EL Wire Set = 3 x 1 metre EL Wire + Driver

3 x 1 Metre of EL Wire, Splitter and Portable Driver for up to 5 metres of EL Wire.

This listing is for:

1) 3 x 1 metre of high quality (3.2mm) Electroluminescent Wire
2) 2 x AA portable Driver (with Flash)
3) Standard 3 way Splitter

The splitter lets you have 3 x 1 metre lengths of EL Wire attached to one driver/inverter - This gives you greater control and flexibility in the design of your costume.

4) 30 x Clear Hoops to make it easy to attach the EL Wire to the costume and also make it removable so you can put it through the washing machine

The EL Wire can be any combination of these colours:

Light Blue, Purple, Deep Blue, Pink, Red, Orange, Yellow, Lime Green, Turquoise-Green and White

The 3.2mm diameter EL Wire is one of our brightest!

To make it easier to design your outfit, below are the dimensions of the inverters and lengths of connecting wires - there are also tips on how to create your costume.

POWER PACK / INVERTER (Driver)

The Power Pack takes 2 x AA batteries and has a built-in voltage inverter that 'inverts' the 3Volts from the batteries up to the 100Volts needed to make the EL Wire glow.

The power pack/inverter dimensions are: 9cm x 3.2cm x 2cm

It has the following controls: On / Flash / Strobe / Off

It has an 8cm wire coming out of it that leads to the...

SPLITTER: The Splitter is 40cm long in total; it is 20cm of wire which then splits into 3 separate strands which are all 20cm long and lead to the...

EL WIRE

There is then another 20-25cm from the connector until the actual glowing start of EL Wire - then there are 3 x 1 metre lengths of gorgeous glowing wire!

Its not complicated or fiddly

This set can turn some clothing into a Tron fancy dress in many ways:

1 metre goes down each arm and

1 metre for the front of the costume

1 metre can go across the back and part way down the arm

1 metre to make a helmet

1 metre for the front of the costume

The whole kit is ready to use - just plug and play!

We have some crazy glowing masks & glasses that go well with this kit - take a look!

EL Tape - 2cm x 12cm - Neon Glow Strip

This is for a 2cm wide and 12cm long Electro-Luminescent Tape.

Currently, in stock we have these colours: Light Blue (Tron Blue), Deep Blue, Red, Pink, Deep Pink, Orange, Yellow, Green and White

On the back of the EL Tape it has wires with connectors already attached:

EL Tape is an incredibly versatile material it can be wrapped around things.

To join it to a costume we recommend our ''''sewable loop & stick-able hook'''' Velcro which allows you to sew one part of the Velcro to your costume while the stick pat goes on the back of this tape. The tape can then be removed from the costume to wash it

EL Tape can even have holes and shapes punched into it and be cut to your chosen shape

This Tape is also available in 25cm, 40cm and 1 metre lengths

A 2 x AA inverter can power four of these 12cm EL Tapes and an 8 x AA inverter can power just over 2 metres of EL Tape.

EL Tape - 2cm by 12cm With Bend Half Way

This is a 2cm wide and 12cm long Electroluminescent Tape with a 45º bend in the middle available in:

Light Blue (Tron Blue), Deep Blue, Pink, Deep Pink, Red, Orange, Grass Green and White

This EL Curve has been designed to help you achieve a realistic Tron costume.

As you can see in the picture below it is perfectly suited for use with straight EL Tape and the EL Hoops

EL Tape, Curve and Hoop in the Tron Style

All our El Wire and Tape comes with wires and connectors attached

Like all EL Tape and EL Wire the EL Curve needs an Inverter/Driver to make it glow

On this EL Curve, the wires are connected in the middle of the bend so either end can be cut to a shape you need

Standard EL Tape with wires and connector

We also stock a wide selection of other EL Tape, EL Wire, Sequencers, Drivers and helpful EL accessories

The EL Curves have loads of other creative uses but are especially good for making realistic Tron costumes

The EL Curve is made from EL Tape which is paper thin (300 micron) so it is incredibly versatile and can be easily attached to costume or even a wall for decoration

We have a whole range of EL Wire, EL Tape and many types of driver/inverters are also available.

If you want any help or advice in planning your EL costume feel free to get in touch

5mm THICK EL Wire @ £4 per metre

The 5mm EL Wire is the least brightest of different diameters of EL Wire, but is ideal for outdoor applications - Sunlight is not good for EL Wire and the thick coating on this wire protects it more.

Some people also prefer this thicker wire for its 'chunky neon cable' look but will not bend into the rightangles required for some letters of the alphabet.when you're making a faux neon sign.

The colours we have at present are:

Light Blue (Tron Blue), Purple, Deep Blue, Pink, Red, Orange, Yellow, Grass Green, Lime Green, Turquoise-Green and White

This 5mm thick EL wire is available in the following lengths: 10cm, 1 metre, 3 metre, 5 metre, 10 metre

This wire comes with a standard connector already attached so that it simply plugs into any EL Driver.

By using 'Splitters' you can also connect different strands to the same Driver.

EL wire has loads of uses!

It has an amazing neon string effect when decorating the interior or exterior of cars, can be used inside and outside of your home and office and can even be threaded into clothes and hats.

This wire comes as 'plug and play' but if you want to get more technical you can be cut into smaller lengths

Our EL inverters can run many lengths of wire as long as the total length of the wire is under the Driver/Inverters maximum capacity

With some care, the EL wire can be attached to speaker wire to make patterns or extend the wire over gaps where it isn't needed

Joining tape and tubing for re-attaching the wire are available from this store

- this is if you want to cut the EL wire and rejoin it or perhaps attach some wire to a different inverter

Cutting the wire into the length you choose is simple... but rejoining it takes care and attention so you will definitely need some wire strippers.

You can happily use the joining tape and heat shrink tubing for a decent join but if the joint is likely to encounter stress (e.g. if it is threaded into clothes that will then be bent and jostled) or if the join may be hard to reach (e.g. behind a panel in a car) then we would advise soldering to avoid future hassle

There are How-tos and a forum on the site to get some great tips

EL Wire Hoodie Set

In this set is everything you need to turn your own normal hoodie into a glowing EL Wire hoodie

With this set you will get:

1) 1.5 metres of 3.2mm EL Wire to outline the hoodie

2) Trigger Driver so you can switch from 'glow mode' to 'incognito' using a switch in your sleeve

3) 30 x Clear Hoops to make it easy to attach the EL Wire to the hoodie and also make it removable so you can put it through the washing machine

The EL Wire outline is in a selection of colours:
Light Blue (Tron Blue), Deep Blue, Pink, Purple, Orange, Red, Yellow, Lime Green, Grass Green and White

We have some crazy glowing masks and glasses that go well with this kit - take a look!

Basic Dance Act EL Wire Set

Take Street Dance to a whole new level with this Glowing EL Wire Set

This set is for a 'plug and play' EL Wire and Driver - but you have to attach it to your own costume

With the set you get:

1) 5 pieces of 1 metre EL Wire in a choice of colours

2) A Trigger Driver that has a 1m long power wire that is able to run down the sleeve, allowing the performer to turn the lights on and off at will

This Driver takes 2 x AA batteries (not supplied) and is powerful enough for 5m of Standard EL Wire (2.5m of Ultra EL Wire)

EL Driver with long plunger trigger control

Trigger Driver for EL Wire

3) A long 2-way splitter and a standard 2-way and 3-way splitter

By 'daisy chaining' the splitters you can have all the lengths of EL Wire attached to this one driver

4) 30 x Clear Hoops to make it easy to attach the EL Wire to the costume and also make it removable so you can put it through the washing machine

The EL Wire can be any combination of these colours:
Light Blue (Tron Blue), Purple, Grass Green, Deep Blue, Pink, Red, Orange, Yellow, Lime Green, and White

EL Wire Dance Act

The whole kit is ready to use - just plug and play!
We have some crazy glowing masks & glasses that go well with this kit - take a look!

Dance Act EL Wire Set = 12 metres of EL Wire + Trigger Driver

Take Street Dance to a whole new level with this Glowing EL Wire Set with a hand controller to switch the lights On and Off

This set is for a 'plug and play' EL Wire and Driver - but you have to attach it to your own costume

With the set you get:

1) 2 pieces of 3 metres EL Wire

2) 6 pieces of 1 metre EL Wire

3) A 'Dance Act' Driver that has a 1.2m long power cord that runs down the arm allowing the performer to turn the lights on and off at will

This driver is powerful enough to make up to 15 metres of EL Wire glow.

4) plus several splitters (3 x 2-way, 2 x 4-way, a spare 5-way and 2 x extenders)

By 'daisy chaining' the splitters you can have all the lengths of EL Wire attached to this one driver

5) 50 x Clear Hoops to make it easy to attach the EL Wire to the costume and also make it removable so you can put it through the washing machine

The EL Wire can be any combination of these colours:

Light Blue (Tron Blue), Purple, Deep Blue, Grass Green, Pink, Red, Orange, Yellow, Lime Green, Turquoise-Green and White

The whole kit is ready to use - just plug and play!

Our EL Wires in Action

Dimensions of the products:

If you are making a costume, it is important to plan it out properly.

For this Dance Act set, the driver is very powerful and so it comes with a separate power pack that takes 8 x AA batteries or a powerful rechargeable (3000mAh) Lithium-Ion Battery and battery charger (please choose the plug type you need)

So here are the dimensions of all the parts plus lengths of wire between them.

THE POWER PACK

Takes 8 x AA batteries (not supplied) and is 6.5cm x 6cm x 3cm

The Rechargeable Li-ion battery is smaller and lighter:

172g (7.3cm x 5.6cm x 2.2cm)

it has a 65cm thin power wire coming out of it that leads to the...

DRIVER

The driver is 6cm x 4cm x 4cm

It has a 1.2m long power lead coming out that ends with an ON/OFF plunger giving you the ability to control the light

It has a 55cm wire coming out of it that leads to a...

SPLITTER

The Splitters are 40cm long in total,

it is 20cm of wire which then splits into the separate strands which are all 20cm long

GLOWING EL WIRE
2 x 3 metres is for the body

6 x 1 metres is for the legs, arms and head

Its not complicated or fiddly - I've just given all those details if you want to plan your costume before you buy the set

EL Wire Dance Act

The whole kit is ready to use - just plug and play!
We have some crazy glowing masks & glasses that go well with this kit - take a look!

EL Tape DOUBLE ENDED 2cm x 1 metre Cut to Make 2 Glowing Strips of Any Length

This is a versatile piece of 2cm wide and 1 metre long Electro-Luminescent Tape.

The EL Tape has wires with connectors attached to BOTH ENDS:

This means it can be cut into two pieces of any length you choose

A 2-way splitter is also provided so you can run both the EL Tapes off of one Driver/Inverter

When cutting EL Tape or Panel it is best to use sharp scissors or craft knife and to seal the cut afterwards with glue and/or clear tape

This EL tape is currently available in these colours:

Light Blue (Tron Blue), Deep Blue, Red, Pink, Deep Pink, Orange, Green, Yellow and White

In the drop down menu below is also the option to buy the EL Tape with a powerful portable driver (8 x AA batteries)

This driver/inverter is powerful enough to drive just over 2 metres of this EL Tape in total and will make the Tape plug and play

(If it is more convenient to have a car-lighter attachment instead of the 8 x AA battery box to power this driver please let us know)

In this store there is a whole selection of drivers available that could power this EL Tape such as Sequencer or Sound Activated Drivers

GLOWING STICKMAN SET = 7.5 metres EL Wire + Driver

1) 6 pieces of 1 metre 3.2mm EL Wire

2) 3 pieces of 50cm 3.2mm EL Wire

3) An EL Driver with either an 8 x AA Power Pack (batteries not supplied) or a rechargeable 3000mAh Li-ion battery (only available in the UK due to airmail postal restrictions)

This driver is powerful enough to glow up to 15 metres of EL Wire

4) 1 x Long 3 Way Splitter, 2 x 3 Way Splitter, 1 x Mini 5 Way Splitter and for the head, a Mini 3 Way Splitter and a 50cm Extender

By 'daisy chaining' the Splitters you can have all 9 metres of EL Wire attached to this one driver/inverter

5) 50 x Clear Hoops to make it easy to attach the EL Wire to the costume and also make it removable so you can put it through the washing machine

The EL Wire can be any combination of these colours:

Light Blue, Lime Green, Pink, Red, Orange, Purple, Yellow, Deep Blue, Turquoise-Green and White

The whole kit is ready to use - just plug and play!

Here is the suggested layout

Dimensions of the products:

If you are making a costume it is important to plan it out properly.

For this glowing man set, the driver/inverter is very powerful and so it comes with a choice of separate power packs.

So here are the dimensions of all the parts plus lengths of wire between them.

THE POWER PACK

Takes 8 x AA batteries (not supplied) and is 12.7cm x 7.02cm x 1.9cm and has a 19cm thin power wire coming out of it that leads to the driver

A 3000mAh rechargeable Li-ion battery which weighs 172g and is 7.3cm x 5.6cm x 2.2cm. This option comes with a 1A intelligent charger. Due to airmail restrictions this is option is only available for UK delivery.

THE DRIVER

The driver is 5.4cm x 3.4cm x 2.9cm and has controls on it - Off, Flashing or On. It has a 55cm wire coming out of it that leads to the...

SPLITTER

The Splitter is 40cm long in total,

it is 20cm of wire which then splits into 3 separate strands which are all 20cm long and lead to the...

EL WIRE

There is then another 20-25cm from the connector until the actual glowing start of EL Wire - then there is 2 X 3metres of gorgeous glowing wire!

1 x 3 metre is for the body

1 x 3 metre is for the legs

ANOTHER SPLITTER!

leads to more...

EL WIRE

20-25cm from the connector until the glowing start of 3 x 50cm EL Wire

These are for the really fun part of designing the expression on the face of your stickman/girl

Its not complicated or fiddly - I've just given all those details if you want to plan your costume before you buy the set

The stickguys and stickgals in these pictures were designed by international party animal Jak Hammer and his amigos!
We have some crazy glowing masks & glasses that go well with this kit - take a look!

GLOWING STICKGIRL SET = 7.5 metres EL Wire + Driver

Turn yourself into a glowing stickgirl!

This set is for a 'plug and play' EL Wire and Driver - but you have to attach it to a costume

*see the diagram below for a suggested setup*

With the set you get:

1) 3 pieces of 1 metre 3.2mm EL Wire

2) 1 piece of 3 metre 3.2mm EL Wire

3) 3 pieces of 50cm 3.2mm EL Wire

4) An EL Driver with either an 8 x AA Power Pack (batteries not supplied) or a rechargeable 3000mAh Li-ion battery (only available in the UK due to airmail postal restrictions)

This driver is powerful enough to glow up to 15 metres of EL Wire

5) 1 x mini 3-way splitter, 1 x standard 3-way splitter, 1 x long 3-way splitter and 1 x 50cm extender

By 'daisy chaining' the splitters you can have all 9 metres of EL Wire attached to this one driver/inverter

6) 50 x Clear Hoops to make it easy to attach the EL Wire to the costume and also make it removable so you can put it through the washing machine

The EL Wire can be any combination of these colours:

Light Blue (Tron Blue), Purple, Deep Blue, Pink, Red, Orange, Yellow, Lime Green, Turquoise-Green and White

The whole kit is ready to use - just plug and play!

Here is the suggested layout - the EL Wire is recommended to run all round the hem of a dress

Dimensions of the products:

If you are making a costume, it is important to plan it out properly.

For this glowing girl set, the driver is very powerful and so it comes with a choice of two different power packs.

So here are the dimensions of all the parts plus lengths of wire between them.

THE POWER PACK

Takes 8 x AA batteries (not supplied) and is 12.7cm x 7.02cm x 1.9cm and has a 21cm thin power wire coming out of it that leads to the driver

THE DRIVER

The driver is 5.4cm x 3.4cm x 2.9cm

It has the controls on it - Off, Flashing or On

It has a 55cm wire coming out of it that leads to the...

SPLITTER

The Splitters are 40cm long in total,

it is 20cm of wire which then splits into 3 separate strands which are all 20cm long

The first has 3 channels and this splits off and lead to the...

EL WIRE

3 x 1 metre for the body

1 x 3 metres is for the skirt

3 x 50cm for the head - - This is the really fun part of designing the expression on the face of your stick man/girl

Its not complicated or fiddly - I've just given all those details if you want to plan your costume before you buy the set

The whole kit is ready to use - just plug and play!

Standard EL WIRE SET = 3 x 3m EL Wire + Driver

With this 'plug and play' set you get

1) 3 pieces of 3 metre 3.2mm EL Wire

2) An EL Driver with an 8 x AA Power Pack

This driver is powerful enough to glow up to 15 metres of EL Wire

3) A 3-way splitter plus an extender

By 'daisy chaining' the splitters you can have all 9 metres of EL Wire attached to this one driver/inverter

4) 30 x Clear Hoops to make it easy to attach the EL Wire to the costume and also make it removable so you can put it through the washing machine

The EL Wire comes in these choice of colours:

Purple, Light Blue, Deep Blue, Pink, Red, Orange, Yellow, Lime Green, Turquoise-Green, and White

AND IS THE BRIGHTEST AVAILABLE 3.2mm WIRE!

The whole kit is ready to use - just plug and play!

Dimensions of the products:

If you are making a costume, it is important to plan it out properly.

For the standard set, the driver/inverter is very powerful and needs a separate power pack

(the basic kit uses a single power/inverter box not much bigger than 2 X AA batteries).

So here are the dimensions of all the parts plus lengths of wire between them.

Feel free to message me if you have any questions

THE POWER PACK

Takes 8 x AA batteries (batteries not supplied) and is 12.7cm x 7.2cm x 1.9cm

it has a 21cm thin power wire coming out of it that leads to the...

Driver

The driver is 6cm x 4cm x 4cm

It has the controls on it - Off, Flashing or On

It has a 55cm wire coming out of it that leads to the...

SPLITTER

The Splitter is 40cm long in total,

it is 20cm of wire which then splits into 3 separate strands which are all 20cm long and lead to the...

EL WIRE

There is then another 20-25cm from the connector until the actual glowing start of EL Wire - then there is 3 x 3 metre lengths of gorgeous glowing wire!

Its not complicated or fiddly - I've just given all those details if you want to plan your costume before you buy the set

The whole kit is ready to use - just plug and play!
We have some crazy glowing masks and glasses that go well with this kit - take a look!

OR FEEL FREE LEAVE A MESSAGE OR CONTACT ME IF YOU WANT ADVICE