Cyber Punk 2077 glowing Samurai patch + driver + power pack

Cyber Punk 2077 glowing samurai

allows you to immerse yourself in the future with this amazing glowing patch. Fix it to the back of your clothing or your gaming chair and simply plug and play.

The Cyber Punk 2077 glowing samurai patch measures 26cm x 23cm and simply plugs into your preferred driver.

It is supplied with 39cm of velcro to easily attach and remove from clothing, since the patch is not washable. Simply sew one side of the Velcro to your clothing and stick the other side to the back of the patch.

If you want to fix the patch onto the back of a gaming chair, use some double-sided tape which is freely available on Ebay or your local DIY store.

All electroluminescent panels need a driver to make them glow. **Please note - DO NOT switch on the driver without first attaching a panel to it.** This item has a few options for you to choose from:

1) NO DRIVER

This is a great option if you already have your own driver you want to use.

Whatever your reason, this option gives you just the Samurai patch - without any driver or external power supplies like the rest of these listed below...

2) Basic Trigger Driver is needed to make the Samurai patch glow. It is powered by 2 x AA batteries (not supplied) and has an On/Off plunger switch, on the end of a 1.2m cable, that can run down the arm of the clothing and used to discreetly turn the glowing Samurai patch on and off.

3) Adaptable Trigger Driver with an 8 x AA battery box. These adaptable trigger drivers make the glowing Samurai patch glow the brightest. The driver's dimensions are 5.3cm x 3.4cm x 2.9cm and it weighs 61g. The battery box plugs straight into the driver. It is fairly large (127mm x 72mm x 19mm) and takes 8 x AA alkaline batteries (not supplied).

For portable uses, this allows the unit to be held on the body while the switch runs down the sleeve to the hand. The switch will latch on when fully pressed down, press for a second time and the switch will latch off.

4) Adaptable Trigger Driver with a 1000mAh Li-ion rechargeable battery pack and intelligent charger. These adaptable trigger drivers make the glowing Samurai patch glow the brightest. The driver's dimensions are 5.3cm x 3.4cm x 2.9cm and it weighs 61g. The Li-ion battery pack plugs straight into the driver.

Much smaller and lighter than the battery box, these powerful Li-ion batteries come with an intelligent charger. Its dimensions are 6.5cm x 3.7cm x 1.8cm and it weighs 81g.

*If you want more than one of the power connectors mentioned above for your EL Driver, they can all be found in our Accessories section, or just click the links in the descriptions you want and be taken to their own pages.*

Fibre Optic Cosmic Cap

Complete the party look with this beautiful high quality, new fibre optic cap with graduated colour change.

This cap has 9 modes:

Press the button once to switch on and the cap will glow
Each press of the button will take you through another colour and the 8th press will bring you to RGB gradual colour change.
Colour order is; Red, green & Yellow, Blue, Green, White, Purple, Blue & Green, colour change

This beautiful cap is perfect for parties, festivals, clubbing and cosplay or at a fancy dress party. What ever your gig, you will look amazing and impress all your friends.

Made from a white material with fibre optics running within the fibres.

This cap comes with a tiny Driver tucked in at the back of the cap, full instructions on how to care for your cap for when you are not using it.

Fibre Optic Masquerade Ball Mask

Complete the party look with this beautiful high quality, new fibre optic masquerade mask with graduated colour change.

This Mask has 9 modes:

Press the button once to switch on and the mask will glow
Each press of the button will take you through another colour and the 8th press will bring you to RGB gradual colour change.
Colour order is; Red, green & Yellow, Blue, Green, White, Purple, Blue & Green, colour change

Made from a white material with fibre optics running within the fibres.

This mask comes with a tiny driver tucked into the feather plume of the mask, full instructions on how to care for your mask for when you are not using it

Glowing Gorilla Mask - Sound Activated with Driver

This mask has a wicked flashing pattern when exposed to sound, making it great for parties, clubs or festivals, day or night - it has a soft comfortable fitting band with a velcro strip that houses the sound activated driver

Glowing Lion Mask - Sound Activated with Driver

This mask has a wicked flashing pattern when exposed to sound, making it great for parties, clubs or festivals, day or night - it has a soft comfortable fitting band with a velcro strip that houses the sound activated driver

Glowing Robot Mask - Sound Activated with Driver

This mask has a wicked flashing pattern when exposed to sound, making it great for parties, clubs or festivals, day or night - it has a soft comfortable fitting band with a velcro strip that houses the sound activated driver

Glowing Stag Mask - Sound Activated with Driver

This mask has a wicked flashing pattern when exposed to sound, making it great for stag nights, parties, clubs or festivals, day or night - it has a soft comfortable fitting band with a Velcro strip that houses the sound activated driver

Glowing Tiger Mask - with sound activated driver

This mask has a wicked flashing pattern when exposed to sound, making it great for parties, clubs or festivals, day or night - it has a soft comfortable fitting band with a velcro strip that houses the sound activated driver

LED side glow fibre optic lighting cable - 10cm to 3 metre lengths

This amazing side glow LED fibre optic lighting cable has been developed to use in conjunction with our LED emitters (which is the light source). Please purchase an LED emitter separately here.

The side glow LED fibre optic lighting cable is a uniform thickness, will not easily break while being able to bend randomly. Completely waterproof and can be cut to any length in situ. It emits no UV or IR energy and produces no heat.

It has a working temperature of -50 to +75 deg Celsius (-58F to 167F).

The side glow LED fibre optic lighting cable is naturally transparent, but changes to the specific colour of the attached LED emitter when said emitter is switched on.

This listing is for 3mm diameter LED fibre optic lighting cable. Please select your preferred length from the drop down menu. If you require longer lengths please get in touch, they are available.

Examples of its' potential uses are hanging lamps, optical fibre curtains, optical fibre water falls, optical fibre ceiling stars etc. It's uses are only limited by your imagination.

Suitable for home decor, retail outlets, restaurants and bars, car modification etc.

Due to external lighting and computer monitor differences, the item's colour may vary slightly from the product image.

Standard Splitter for EL Wire, EL Tapes, EL Panels- 2 Way up to 6 Way

These Standard splitters make your glowing costume or EL project exactly how you want.

These Splitters allow you to run up to six separate strands of EL wire from just one Driver/Inverter (or another Splitter).

The Splitter works for EL Wire, EL Tape or EL Panels.

The Splitter is 40cm in total length and the connector wire is 20cm long.

These Splitters are available in: 2 Way / 3 Way / 4 Way / 5 Way/ 6 Way

*ALL the EL Wire, EL Tapes and EL Panels that we supply comes with a 'Connector' already attached so they plug straight into a Driver*

EL wire has loads of uses

This neon wire looks amazing when decorating the interior or exterior of cars, can be used inside and outside of the home and can even be threaded into clothes and hats.

It is a cliché to say you are only limited by your imagination but with EL wire it is true!!!

If you have not seen it before it is like a really long glow stick that lasts over 5,000 hours

We're sure you will be amazed - feel free to message us with any questions you may have.

I already have an EL driver

Use this option if you already have your own EL driver.

Mains PSU - UK mains to 12V

This is a plug that goes into the mains power and then converts the mains AC power to 12V DC which is what many of our EL Drivers are powered by.

Since EL Wire is very low power, we only have these power supply units that output a maximum of 1A.

These power supply units are recommended to be used with our adaptable drivers.

If you have never seen EL wire have a look at my other items - it is basically a thin cool glowing neon wire

EL wire has loads of uses

It looks amazing when decorating the interior or exterior of cars, can be used inside and outside houses and can even be threaded into clothes and hats

If you have not seen it before it is like a really long glow stick that lasts around 5,000 hours

We're sure you will be amazed - feel free to message us with any questions.

Sewable EL Wire - Easy Sew Tag @ £3.50 per metre

This handy item is a 2.3mm EL wire with sewable tag running along it; it is available in lengths of 50cm, 1m, 3m, 5m and 10 metre.

(EL wire needs a Driver to make it glow - available from £4 in the Inverter/Driver section of the website).

EL Wire twisted into a spiral

The wire is available in any of these colours:

Light Blue (Tron Blue), Purple, Deep Blue, Pink, Red, Orange, Yellow, Lime Green, Turquoise-Green (being discontinued), Grass Green and White

Because the EL naturally glows blue/green the brightest colour of the wire is the Light Blue, Lime Green and White. The least bright are the red and purple as they have to be filtered the most to get the colours right.

The wire has a connector already attached and ready to clip into an EL Driver - THE DRIVER HAS TO BE BOUGHT SEPARATELY

By using splitters you can also connect different strands to the same Driver.

EL wire has loads of uses

It looks amazing when decorating the interior or exterior of cars and motorbikes and can be used inside and outside of your home and office and can even be threaded into clothes and hats.

Our Drivers can run many lengths of EL wire as long as the total length of the wire is under the Driver's maximum capacity

Cutting the wire into the length you choose is simple

EL Wire Repair Kit

Contents of the elwirecraft EL Repair Kit:

1) Instruction Booklet
2) 5 x Male EL Connector (that attach to the EL Wire itself)
3) 6-way Splitter
4) Copper Tape
5) Wide and Thin Heatshrink Tubing
6) End Caps

You Will also Need
1) Wire strippers
2) Soldering Iron + Solder
3) Scalpel
4) Heat gun or lighter
5) Helping Hands (if possible)

EL Wire Care

EL Wire is a very robust material - it can withstand fairly extreme temperatures between -20°C and 50°C. It is durable and the wire itself is water resistant. If the wire is likely to get wet or even be in a humid environment then make sure the end of the wire has been made fully waterproof as the connection point is sensitive to moisture.

Even if the material itself is hardy, like any electronics it has to be looked after if you want it to last a long time.
This goes double if the EL Wire is going to be worn and where it will be exposed to various stresses that electrical items are sensitive to.

There are some tips on the back page to get the most out of your EL Wire, but you must also remember that the life of your
EL Wire will be reduced if it is exposed to repeated bending stress, extreme pulling tension or humid conditions.

EL WIRE WITH CONNECTORS ATTACHED

All the EL Wire, EL Tape and EL Panels supplied by elwirecraft already have connectors attached and are ready to plug straight into a driver

(please note we always have stocks of EL Wire with connectors attached in lengths of 10cm, 50cm, 1metre, 3metre, 5metre, 10 metre, 15 metre and 25 metre)

The connectors for EL wire are generally universal - these are connectors that either attach to an EL Driver or will fit into a splitter that comes off of a driver

If you are cutting a piece of EL wire you may also want to put a cap on the end of it so these are supplied too

Cutting EL Wire couldn't be simpler, but re-attaching it is fairly easy but takes a little time and patience and is explained step by step in the instruction booklet

We can supply more copper tape and heat-shrink tubing here

- - - - - - - - - - - - - - - - - -

If you have never seen EL wire have a look at my other items - it is basically a thin cool glowing neon wire

EL wire has loads of uses
This neon wire looks amazing when decorating the interior or exterior of cars, can be used inside and outside houses and can even be threaded into clothes and hats

If you have not seen it before it is like a really long glow stick that lasts over 5,000 hours

We're sure you will be amazed - feel free to message us with any questions

Sound Activated Driver for 3 - 10m

This is a Sound Activated Driver that's part of our Adaptable range so it can accept a number of power supplies.

The Driver will make between 3m and 10 metres of EL Wire glow when reacting to sound, there is a sensitivity dial for control of the Sound Activated response.

As explained in detail below, these Adaptable Drivers are very versatile with a whole selection of Power supplies, from mains, batteries to direct 12V etc.

Its dimensions are 6cm x 4cm x 2.5cm (L x W x H) and it has a weight of 38g.

EL Driver Options:

We have found it is impossible to guess how you will be using the EL Wire, EL Tape and Drivers, so you will see on this website we have tried to give you as many choices as possible.

This driver is no exception as it also has a range of power supplies that hopefully cover most uses:

1) ONLY THE DRIVER

If you have your own 12V 5.5mm/2.1mm input you want to use or you may be using the 2 way power supply splitter that lets you use 2 drivers off one battery (available below)

2) Crocodile Clips

Perfect if you already have your own 12V battery to run this driver

3) 8xAA Battery Box

This 8 x AA Battery Box will plug straight into the driver. It is fairly large (126mm x 76mm x 19mm) but will make this EL Driver portable

4) 3 x 18650 Rechargeable Battery Box

This 3 x 18650 Rechargeable Battery Box will plug straight into the driver. It is fairly large (76mm x 60mm x 22mm) and the leads for the output are 15cm long but will make this EL Driver portable.

5) Rechargeable Li-ion Battery

Much smaller and lighter than the Battery Box, these powerful Li-ion batteries come in a range of sizes

1800mAh (flat): 145g (10.3cm x 5.5cm x 1.1cm)

1800mAh (square): 122g (5.6cm x 3.8cm x 3.1cm)

3000mAh: 172g (7.3cm x 5.6cm x 2.2cm)

5000mAh: 265g (6.0cm x 5.8cm x 3.9cm)

All of these Li-ion Batteries come with an intelligent charger as standard.

6) Mains Powered

This handy PSU can be used to make this EL Driver powered off of Mains Electricity (UK, US or Euro plugs are available)

7) Car Lighter Adaptor

This adaptor plugs into the car lighter socket. It is fused and ends with a 5.5mm/2.1mm jack plug so it can be used with any of our 12v Drivers or accessories

9) 2 way Splitter for 12V Power Input (5.5mm)

If you're thinking of running two of these units off of one power source, then get yourself one of these splitters.

*If you want more than one of the power connector mentioned above for your EL Driver, then just click on one of the descriptions and it should take you to a page where you can buy just the power connector on its own*

Remote Control

You can use this Remote Control Unit by placing the Controller between the Power Source and the Driver

You can use several controllers with just one hand-held remote unit if you want to switch several drivers at once

The Remote Control Unit is not available in the drop down menu above - please click on the image to get the full details of this handy EL Accessory and add it to your basket.

*All the EL wire we supply comes with a connector, so they plug straight into the driver*

- - - - - - - - - - - -

EL wire has loads of uses

It looks amazing when decorating the interior or exterior of cars, can be used inside and outside houses and can even be threaded into clothes and hats

It is a cliché to say you are only limited by your imagination but with EL wire it is true!!!

If you have not seen it before it is like a really long glow-stick that lasts around 5,000 hours

We're sure you will be amazed - feel free to message me with any questions

EL Wire Sample Packs

So you've not used or seen Electroluminescent Wire before and you are curious to see what the colours are like in the different types and thicknesses and what you can do with it.

The beauty of EL Wire is its easy to use and comes ready to plug and play. Our samples packs have a good selection of EL Wire in all its different forms and colours.

Choose from the drop down menu:

1) All Blue - Mix of Types
Choose this option if you want try out our Blue wires, and we will send you a selection of different wires and diameters

In this EL Wire Sample Pack you will get:
1) 1 x 1m length of 1.0mm EL Wire in Light Blue
2) 1 x 1m length of 2.3mm EL Wire in Light Blue
3) 2 x 50cm lengths of 3.2mm EL Wire in Light Blue and Deep Blue
4) 1 x 1m length of 5mm EL Wire in Light Blue
5) 2 x 50cm length of Sewable EL Wire in Light Blue and Deep Blue
6) 1 x 1m length of Stiff EL Wire in Aqua
7) 2 x 50cm lengths of Maxi EL Wire in Blue and Purple (this has a blue tone to it)
8) 1 x 2 x 12cm length of Light Blue EL Tape
9) 1 x Mains 5-15m Driver/Inverter
10) 1 x 8xAA Battery Box
11) 1 x standard 6-way splitter (40cm long) in black
12) 1 x standard 6-way splitter (40cm long) in white
13) 1 x mini 2-way splitter (20cm long) in black.

2) All White - Mix of Types
Choose this option if you want try out our White wires, and we will send you a selection of different wires and diameters.

In this EL Wire Sample Pack you will get:
1) 1 x 1m length of 1.0mm EL Wire in White
2) 1 x 1m length of 2.3mm EL Wire in White
3) 1 x 1m length of 3.2mm EL Wire in White
4) 1 x 1m length of 5mm EL Wire in White
5) 1 x 1m length of Sewable EL Wire in White
6) 1 x 1m length of Stiff EL Wire in White
7) 1 x 1m length of Maxi EL Wire in White
8) 1 x 2 x 12cm EL Tape in White
9) 1 x Mains 5-15m Driver/Inverter
10) 1 x 8xAA Battery Box
11) 1 x standard 6-way splitter (40cm long) in black
12) 1 x standard 6-way splitter (40cm long) in white
13) 1 x mini 2-way splitter (20cm long) in black

3) Mixture of all Colours and Types
Choose this option if you want try out all of our colours, and we will send you a selection of different wires and diameters

In this EL Wire Sample Pack you will get:
1) 1 x 1m length of 1.0mm EL Wire in White
2) 1 x 1m length of 2.3mm EL Wire in Red
3) 1 x 1m length of 3.2mm EL Wire in Light Blue
4) 1 x 1m length of 5mm EL Wire in Orange
5) 1 x 1m length of Sewable EL Wire in Yellow
6) 1 x 1m length of Stiff EL Wire in Lime
7) 1 x 1m length of Maxi EL Wire in Pink
8) 1 x 2 x 12cm EL Tape in Light Blue
9) 1 x Mains 5-15m Driver/Inverter
10) 1 x 8xAA Battery Box
11) 1 x standard 6-way splitter (40cm long) in black
12) 1 x standard 6-way splitter (40cm long) in white
13) 1 x mini 2-way splitter (20cm long) in black

Our wires are available in any of these colours:
Light Blue (Tron Blue), Purple, Deep Blue, Pink, Red, Orange, Yellow, Grass Green, Lime Green and White

Our wires are available in any of these types: 1.0mm, 1.5mm, 2.3mm, 3.2mm, 5mm, Stiff, Ultra and sewable

All of our sample packs come with:

1) 5-15m adaptable driver with (mains plug- relevant to your location) (email us - if you would like a battery option)

2) Splitters to 'drive' all the wires at the same time.

3) 2 x 12cm EL Panel

Because the EL naturally glows blue/green the brightest colour of the wire is the Light Blue, Lime Green and White.

The least bright are the red and purple as they have to be filtered the most to get the colours right.

The wire has a connector attached and so is ready to clip into an EL Driver.

A wide selection of other EL Tape, EL Panels, Sequencers, Drivers and helpful EL accessories are available from our store

FEEL FREE TO CONTACT US IF WE DO NOT HAVE YOUR REQUIRED LENGTH OF EL WIRE LISTED AS WE TAKE CUSTOM ORDERS - TPLEASE BE AWARE THERE IS A MINIMUM ORDER REQUIREMENT FOR CUSTOM ORDERS.

EL wire has loads of uses

It has an amazing neon string effect when decorating the interior or exterior of the home, cars, motorbikes, bicycles and trailers. It can be used to make faux neon signs and attached to costumes and even be threaded into clothes and hats. It can be used as safety lighting and mood lighting.