Adjustable Speed Driver for up to 3 metres CHASING EL Wire (2 x AA)

This driver is specifically for use with Chasing EL Wire and will not connect or light up standard EL Wire

EL Chasing Wire

It has a mode button that switches between:

OFF - Continuous ON - Adjustable

When the driver is in 'Adjustable' mode, you can control the speed of the chasing effect from a slow crawl right up until the speed is a blur.

This small portable unit will light up to 3 metres of standard chasing wire or 1 metre of ULTRA chasing EL Wire.

For use with this driver, we currently stock 50cm, 1m and 3metre lengths of standard chasing EL Wire

We have specially made Chasing Splitters to connect 3 pieces of 1m Chasing EL Wire to this one Driver

or if you are using ULTRA Chasing EL Wire then it must be either a single 1metre length or you can use the splitters with 3x 33cm strands or 2x 50cm pieces

(ULTRA Chasing EL Wire is much brighter and requires more power to make it glow)

Its dimensions are: 10.5cm x 3.2cm x 2cm (L x W x H)

** REMEMBER - EL Drivers if left switched on, will keep running and draining the battery while it is switched on even if there is EL Wire or EL Tape attached to it or not**

EL wire has loads of uses

It looks amazing when decorating the interior or exterior of cars, can be used inside and outside of the home and can even be threaded into clothes and hats

It is a cliché to say you are only limited by your imagination but with EL wire it is true!

If you have not seen it before it is like a really long glow-stick that lasts over 5,000 hours

We're sure you will be amazed - feel free to message us with any questions you may have.

Driver for up to 10 metres CHASING EL Wire

Driver for up to 10 metres Chasing EL Wire

This driver is specifically for use with Chasing EL Wire and will not connect or light up standard EL Wire.

EL Chasing Wire

This Portable Chasing EL Driver powerful is enough for 3 - 10 metres of standard Chasing EL Wire or 1 - 3 metres of Ultra Chasing EL Wire and is powered by 4 x AAA batteries (not supplied).

For use with this driver, we currently stock 50cm up to 10 metre lengths of standard chasing EL Wire

We have specially made Chasing Splitters to connect 3 pieces of 1m Chasing EL Wire to this one Driver

or if you are using ULTRA Chasing EL Wire then it must be either a single 3metre length or you can use the splitters with 1m strands.

(ULTRA Chasing EL Wire is much brighter and requires more power to make it glow)

The Chasing EL Driver is: 8.5cm x 4.5cm x 3cm (L x W x H)

** REMEMBER - EL Drivers if left switched on, will keep running and draining the battery while it is switched on even if there is EL Wire or EL Tape attached to it or not**

FEEL FREE TO CONTACT US IF WE DO NOT HAVE YOUR REQUIRED LENGTH LISTED

- - - - - - - - - - - -

EL wire has loads of uses

It looks amazing when decorating the interior or exterior of cars, can be used inside and outside houses and can even be threaded into clothes and hats

It is a cliché to say you are only limited by your imagination but with EL wire it is true!!!

If you have not seen it before it is like a really long glow-stick that lasts over 5,000 hours

We're sure you will be amazed - feel free to message us with any questions

2 Way Switch Splitter with "Middle: ALL OFF"

These splitters are a handy and cheap way of making different parts of your EL costume/project light up

The EL Splitter Switch is simply a 2 way splitter with a 3 switch on it

The switch has three positions:

Switch to the left: Channel A ON + Channel B OFF

Switch to the right: Channel A OFF + Channel B ON

Switch in the middle: Both Channels OFF

(we also sell a different "Both ON" switch splitter - on this type, the Switch in middle is both channels ON)

The spitter is 20cm in total and it is often used with extender wires running down the sleeve to allow the switch splitter to sit in your hand

This "Middle: All OFF" Switch Splitter is useful is you want to overlay two different designs onto one project

This is a mask that was made with two different designs on it. On one channel of the splitter is the EL Wires of the Alien Face, the other channel connects to the EL Wires for the Crazy Face

The wearer can have the mask with the Crazy Face showing and then, when they want to freak people out, just flick the switch across so the Alien Face appears

We also provide this splitter where the Middle setting is BOTH ON - click here to have a look

*ALL the EL wire we supply comes with a universal EL connector, so they plug straight into one of these splitters or a driver*

- - - - - - - - - - - -

EL wire has loads of uses

This neon wire looks amazing when decorating the interior or exterior of cars, can be used inside and outside houses and can even be threaded into clothes and hats

It is a cliche to say you are only limited by your imagination but with EL wire it is true!!!

If you have not seen it before it is like a really long glow stick that lasts over 5,000 hours

We're sure you will be amazed - feel free to message us with any questions

Enclosed Battery Box (8 x AA) - 12V PORTABLE POWER PACK

This handy item is an enclosed battery box that takes 8 x AA batteries (batteries not supplied) and gives an output of 12v.

*Please note this is just a battery box, IT IS NOT AN EL DRIVER/INVERTER. They are available as a power supply for our EL Drivers or EL Sequencers.*

The size of this power pack is:

127mm x 72mm x 19mm and the lead for the output is 17cm long with a 2.1mm/5.5mm plug on the end.

This is a useful item for when you need to power a 12v appliance that you want to make portable

REMEMBER:

Standard alkaline batteries are 1.5v each, so 8 of them will make 12v, however rechargeable batteries are only1.2v each, so 8 of them in this battery pack will only produce 9.6v.

- - - - - - - - - - - - - - - - - -

These battery packs are used to power powerful driver/inverters for EL wire

If you have never seen EL wire have a look at my other items - it is basically a thin cool glowing neon wire

EL wire has loads of uses

This neon wire looks amazing when decorating the interior or exterior of cars, can be used inside and outside houses and can even be threaded into clothes and hats

If you have not seen it before it is like a really long glow stick that lasts around 5,000 hours

We're sure you will be amazed - feel free to message us with any questions.

Light Painting Kit - Use EL Wire With a Camera

Light painting is a modern and evolving art form. New techniques and are being discovered and the effects are breathtaking
https://elwirecraft.co.uk/wp-admin/edit.php?post_type=product
If you want to unleash the creative potential of your camera with amazing results then maybe you could try your hand at light painting

With his kit you get

1) EL Driver

Based on a standard 2xAA EL Driver, but instead of a push button on the front scrolling through the settings there is a long 1metre (35inch) wire coming out of the driver that ends with an ON/OFF click plunger (the trigger)

2) EL Wire

5 pieces of robust 1m long 3.2mm diameter EL Wire in a choice of colours in any combination of these colours:

Light Blue (Tron Blue), Purple, Deep Blue, Pink, Red, Orange, yellow, Lime Green, Green and White

3) 5-way splitter

Allows you to have up to 5 pieces of EL Wire lit up by the driver at once.

Either message us with your choice of colours
or select one of these:
LAPOG = Lime, Light Blue, Purple, Orange and Green
LAPWB = Lime, Light Blue, Purple, White and Deep Blue
LARYB = Lime, Light Blue, Red, Yellow and Deep Blue
LARYP = Lime, Light Blue, Red, Yellow and Pink
LARYW = Lime, Light Blue, Red, Yellow and White

Good luck with your light painting experiments!

Professional Light Painting Set - Use EL wire with your camera

Light painting is a modern and evolving art form. New techniques are being discovered and the effects are breathtaking.

This light painting set has been specially designed for those wanting to take their art further with a wider range of effects that can be created using the different properties of specialist EL wires.

The set also includes a versatile electroluminescent panel which can be cut to shape or a stencil easily placed over it.

Please select your preferred colour options for the following sets from the drop down menu:

Set 1 colour options:

3 x 1m lengths of 3.2mm EL wire in Light Blue, Purple and Yellow,
1 x 50cm length of stiff EL wire in Deep Blue,
1 x 1m length of maxi EL wire in Pink,
1 x 10cm length of 5mm EL wire in Light Blue,
1 x 5cm x 8cm EL panel in Light Blue,

Set 2 colour options:

3 x 1m lengths of 3.2mm EL wire in Yellow, Orange and Red,
1 x 50cm length of Stiff EL wire in Gold,
1 x 1m length of Maxi EL wire in Orange,
1 x 10cm length of 5mm EL wire in Red,
1 x 5cm x 8cm EL panel in Light Blue,

Set 3 colour options:

3 x 1m lengths of 3.2mm EL wire in Deep Blue, Grass Green and Purple,
1 x 50cm length of Stiff EL wire in Light Blue,
1 x 1m length of Maxi EL wire in Deep Pink,
1 x 10cm length of 5mm EL wire in Lime Green,
1 x 5cm x 8cm EL panel in Light Blue,

Your preferred colour selection will include the following:

1) 1 x EL trigger driver

This driver gives you good control of lighting the wire by having a 1m long cord with a trigger switch on the end. The button either latches into place or on half press, stays lit for as long as it is help down.

2) 1 x mini splitter

Using splitters enables you to make more than one EL wire or EL panel glow at a time.

3) 3.2mm EL wire

This EL wire has a slightly thicker sleeve than our standard EL wire, giving it extra protection against bending stress.

4) Stiff EL wire

This rigid EL wire can be formed and will hold any shape you bend it into.

5) Maxi EL wire

This is a finer wire that is not so rigid, but it will hold its shape.

6) 10cm length of 5mm EL wire

This small and firm length of wire is perfectly suited to be used as a light wand.

7) 5cm x 8cm EL panel

This unique light and versatile material can be cut to any shape, or if you want to reuse it then mask out the areas you don't want lit. The panel doesn't heat up so you can mask it with any materials including coloured cellophane or acetates.

We are sure you'll enjoy your light painting experiments, a very popular and growing art form!

3 x 18650 Battery Box

This handy item is a battery box that takes 3 x 18650 batteries and gives an output of just under 12V

*Please note this is just a battery box IT IS NOT AN EL DRIVER/INVERTER. They are available as a power supply for our EL Drivers or EL Sequencers.*

18650 batteries are the long round flat ended rechargeable 'INR' or 'IMR' batteries which have become popular since they are used in vaping rigs.

We have made this battery box to power the 12v EL Drivers and Sequencers,

The 18650 batteries are 3.7v each, so the power input from this Battery Box with 3 is a total of 11.1V

We have found this barely makes a difference when powering EL Drivers compared to the convenience of these rechargeable batteries

This Battery Box comes with a standard 2.1mm/5.5mm connector

The size of the Battery Box power pack is 76mm x 60mm x 19mm and the output lead is 250mm long.

- - - - - - - - - - - - - - - - - -

These battery packs are used to power powerful driver/inverters for EL wire

If you have never seen EL wire have a look at my other items - it is basically a thin cool glowing neon wire

EL wire has loads of uses

This neon wire looks amazing when decorating the interior or exterior of cars, can be used inside and outside houses and can even be threaded into clothes and hats

If you have not seen it before it is like a really long glow stick that lasts around 5,000 hours

We're sure you will be amazed - feel free to message us with any questions.

Adaptable Driver for 5-15m EL Wire - Flashing Option

This handy item is a 12v driver with a variety of power inputs that will run between 5 and 15 metres of EL Wire.

The Driver has a switch on the side with 3 different positions Off - Flash - Continuous On.

As explained in detail below, these Adaptable Drivers are very versatile with a whole selection of Power inputs (Mains, Batteries, Direct 12V etc)

The size of the Driver is: 5.4cm x 3.4cm x 2.9cm and weighs 61g.

Using splitters, this Driver can run as many strands as you like as long as the total is under 15 metres.

EL Driver Options:

We have found it is impossible to guess how you will be using the EL Wire, EL Tape and Drivers, so you will see on this website we have tried to give you as many choices as possible.

This driver is no exception as it has a range of power inputs that cover most potential uses, please choose one of these from the drop-down menu:

1) ONLY THE DRIVER

Maybe you have your own 12V 5.5mm/2.1mm input you want to use, perhaps you will be using one of the 2-way power splitters?

Whatever your reason, this option gives you just the driver (as in the pic above) - without any external power connectors like the rest of these listed below...

2) Crocodile Clips

Perfect if you already have your own 12V battery to run this driver

3) 8xAA Battery Box

This 8xAA Battery Box will plug straight into the driver. It is fairly large (127mm x 72mm x 19mm) but will make this EL Driver portable.

4) 3 x 18650 Rechargeable Battery Box

This 3 x 18650 Rechargeable Battery Box will plug straight into the driver. It is fairly large (76mm x 60mm x 19mm) and the leads for the output are 15cm long but will make this EL Driver portable.

5) Rechargeable Li-ion Battery

Much smaller and lighter than the Battery Box, these powerful Li-ion batteries come in a range of sizes

1000mAh: 81g (6.5cm x 3.7cm x 1.8cm)

1800mAh (square): 145g (5.6cm x 3.8cm x 3.1cm)

3000mAh: 172g (7.3cm x 5.6cm x 2.2cm)

5000mAh: 265g (6.0cm x 5.8cm x 3.9cm)

All of these Li-ion Batteries come with an intelligent recharger

6) Mains Powered

This handy PSU can be used to make this EL Driver powered off of Mains Electricity (UK, US or EU plugs are available)

7) Car Lighter Adaptor

This adaptor plugs into the car lighter socket. It is fused and ends with a 5.5mm/2.1mm jack plug so it can be used with any of our 12v Drivers or accessories

8) 2 way Splitter for 12V Power Input (5.5mm)

If you're thinking of running two of these units off of one power source, then get yourself one of these splitters.

Please note this is a Splitter from the Battery to the Driver, so you would only need one Battery pack for 2 x Drivers.

Most people also use Splitters that come from the Driver to the EL Wire (so you only need 1 x Driver for many EL Wires) - you can get those types of EL WIRE SPLITTERS HERE

*If you want more than one of the power connector mentioned above for your EL Driver,

They can all be found in our Accessories section, or just click the description you want and be taken to its own page*

Remote Control

You can use this Remote Control Unit by connecting the Controller between the Power Source and the Driver.

You can use several controllers with just one hand-held remote unit if you want to switch different drivers at once.

The Remote Control Unit is not available in the drop down menu above - please click on the link to get the full details of this handy EL Accessory and add it to your basket

*All the EL wire we supply comes with a connector, so they plug straight into the driver

EL wire has loads of uses!

This neon wire looks amazing when decorating the interior or exterior of cars, can be used inside and outside houses and can even be threaded into clothes and hats

It is a cliché to say you are only limited by your imagination but with EL wire it is true!!!

If you have not seen it before it is like a really long glow stick that lasts over 5,000 hours

We're sure you will be amazed - feel free to message us with any questions.

12V Rechargeable 5000mAh Li-ion Battery for EL Driver and LED

This battery pack has been specially made for EL Wire Craft and are made with the highest quality Lithium Polymer technology.

While trying out different battery systems we found that many of them exaggerated the milliamp/Hour ratings, these batteries are within 10% of the rating at which they have been given.

They also feature overcharge protection.

They do not have their own on/off switch as we found this was unnecessary and just added another element that could fail.

The battery pack weight and dimensions are: 265g and (6.0cm x 5.8cm x 3.9cm)

Input power is 12.6V DC with an output of 12V DC. There is an over-charge / discharge protection.

The intelligent 1A Li-ion charger (supplied as standard) has a UK plug. It is recommended these Li-ion batteries are best charged with these chargers

12V Rechargeable Li-ion batteries & chargers

These batteries have been specially made for EL Wire Craft and are made with the highest quality Lithium Polymer technology.

Whilst trying out different battery systems, we found that many of them exaggerated the milliamp/Hour ratings. These batteries are within 10% of the rating at which they have been given.

They also feature overcharge protection.

They do not have their own on/off switch as we found this was unnecessary and just added another element that could fail.

We have these batteries in five different sizes with the following weights and dimensions:

1000mAh: 81g (6.5cm x 3.7cm x 1.8cm)

1800mAh (Square): 145g (5.6cm x 3.8cm x 3.1cm)

3000mAh: 172g (7.3cm x 5.6cm x 2.2cm)

5000mAh: 265g (6.0cm x 5.8cm x 3.9cm)

15Ah: 725g (14.0cm x 6.5cm x 4.7cm)

SPECS:

Capacity: 1000mAh, 1800mAh, 3000mAh or 5000mAh

Input power: DC 12.6V

Output: DC 12V

Over-charge / discharge protection: Yes

These Li-ion batteries are best charged with dedicated Li-ion Intelligent Chargers

The 15Ah has an overcharge protection up to 15A so can take a larger current draw

AC Mains intelligent chargers come with UK plugs and are available in a choice of:

No Charger - if you already have your own intelligent Li-ion battery charger

1A Charger - This will charge the Li-ion batteries at a max of 1A per hour

2A Charger - This will charge the Li-ion batteries at a max of 2A per hour

EL Tape Tron Sacral Piece

This EL Tape has been designed to be worn down the base of the spine for a realistic Tron Costume.

The beautiful 'Tron Circuit' style can be worn on any part of the body to create an amazing effect.

The piece is 18cm tall and 9cm wide and available in these colours:

Light Blue (Tron Blue), White and Orange

The EL Tape needs a Driver to make it glow

The Powerful Portable 8xAA Driver can power up to ten of these pieces.

Other Driver/Inverters and glowing EL parts of Tron costumes are available in our store.

All our El Wire and Tape comes with wires and connectors attached

Standard EL Tape with wires and connector

This EL Panel has loads of other creative uses but are especially good for making realistic Tron costumes

It is made from EL Tape which is paper thin (300 micron) so it is incredibly versatile and can be easily attached to costume or even a wall for decoration

We have a whole range of EL Wire, EL Tape and many types of driver/inverters are also available.

If you want any help or advice in planning your EL costume feel free to get in touch.

EL Tape TRON SET = 2 x 25cm Tape + EL Hoops + Driver

This amazing kit contains just what you need for a great glowing Tron costume:

1) 2 pieces of 2cm x 25cm EL Tape

2) 2 pieces 6cm EL Hoops

3) 4 Way Black Splitter

4) Powerful portable Driver/Inverter powered by 8xAA batteries (not supplied) or rechargeable Li-ion battery.

5) It also comes with just over 50cm of Velcro - sticky on one side and sewable on the other to help you attach the El Tape and EL Hoops to a costume.

The EL Tape and EL Hoops can be any combination of these colours:

Light Blue (Tron Blue), Deep Blue, Pink, Green, Orange, and White

The whole kit is ready to use - add batteries and plug and play!

Dimensions of the products:

If you are making a costume, it is a good idea to plan it out properly.

So here are the dimensions of all the parts plus lengths of wire between them:

THE POWER PACK

Takes 8 x AA batteries (not supplied) and is 6.5cm x 6cm x 3cm

it has a 65cm thin power wire coming out of it that leads to the...

DRIVER

The driver is 6cm x 4cm x 4cm

It has the controls on it - Off, Flashing or On

It has a 55cm wire coming out of it that leads to the...

SPLITTER

The 4 Way Splitter is 40cm long in total,

it is 20cm of wire which then splits into 4 separate strands which are all 20cm long and lead to the...

EL TAPE

The EL Tape has a 20cm wire on it before 25cm of glorious glowing EL Tape

The tape is just 350 microns thick - that is 1/3rd of a millimetre!

Sticky back Velcro is supplied that is the exact width of the EL Tape - be careful putting it on as that glue is VERY sticky

You must sew the other part of the Velcro onto the costume making it very convenient to attach and remove

Of course, you don't need to use the Velcro and fix it any way you choose

EL HOOPS

Two channels of the Splitter lead to these glowing discs of EL Tape that give your costume and authentic Tron look

Its not complicated or fiddly - we've just given all those details if you want to plan your costume before you buy the set - feel free to message us if you have any questions.

OR CONTACT US IF YOU WANT ADVICE PLANNING YOUR SET

We have some crazy glowing masks & glasses that go well with this kit - take a look!

This EL Tape comes with a standard connector so simply plugs into any EL inverter - this makes it easy to change between coloured wire on one inverter.

By using splitters you can also connect different strands to the same Inverter / Driver

USB Rechargeable 3000mAh Li-ion Battery

These batteries have been specially made for EL Wire Craft and are made with the highest quality Lithium Polymer technology.

(*Li-ion Batteries are only available to the UK due to airmail postal restrictions)

These Rechargeable Batteries have been designed to work with our USB EL Drivers

but will supply power to any device that has a USB input

These Li-ion Batteries can recharged using any USB port.

This battery back weighs 74 grams and is 71mm x 44mm x 8mm (L x W x H).

SPECS:

Capacity: 3000mAh

Input power: DC 5.2V

Output: DC 4.5V - 5.2V

Over-charge / discharge protection: Yes

EL Tape TRON SET = 2 x 40cm EL Tape + EL Hoops + EL Wire + Driver

This amazing item consists of:

1) 2 pieces of 2cm x 40cm EL Tape,

2) 4 x 6cm EL Hoops,

3) 2 pieces of 1m x 1.5mm EL Wire,

4) 2 x 4-way splitters and a 2-way splitter,

5) and a powerful portable Driver/Inverter with either an 8xAA battery box (batteries not supplied) or a 3000mAh rechargeable Li-ion battery (only available in the UK due to airmail postal restrictions),

6) It also comes with 80cm of Velcro - sticky on one side and sewable on the other to help you attach the tape and hoops to a costume

The EL Wire can be any combination of these colours:

Light Blue (Tron Blue), White and Orange

The whole kit is ready to use - just plug and play!

Dimensions of the products:

If you are making a costume, it is a good idea to plan it out properly.

For this set, the driver is very powerful and comes with a separate power pack.

So here are the dimensions of all the parts plus lengths of wire between them.

Feel free to message us if you have any questions.

THE POWER PACK

Takes 8 x AA batteries (not supplied) and is 6.5cm x 6cm x 3cm

it has a 65cm thin power wire coming out of it that leads to the...

DRIVER

The driver is 6cm x 4cm x 4cm

It has the controls on it - Off, Flashing or On

It has a 55cm wire coming out of it that leads to the...

SPLITTER

The Splitter is 40cm long in total,

it is 20cm of wire which then splits into 3 separate strands which are all 20cm long - 2 of them then lead to...

2 x EL TAPE

The EL Tape has a metre of wire on it before the 2cm X 40cm super-bright glow of the EL Tape

The tape is just 350 microns thick - that is 1/3rd of a millimetre!

Sticky back Velcro is supplied that is the exact width of the EL Tape - be careful putting it on as that glue is VERY sticky

You must sew the other part of the Velcro onto the costume making it very convenient to attach and remove

Of course, you don't need to use the Velcro and can fix it any way you choose

EL HOOPS

Two channels of the splitter lead to these glowing discs of EL Tape onto the shoulders

These 6cm diameter hoops also come with sticky back Velcro discs to attach them to your costume

EL WIRE

This thin but very bright EL Wire gives an amazing effect as it runs from the hoop near the collar, over the shoulder, down the back and round the waist where it meets the other EL Hoop

SPLITTERS

This is how we recommend using the splitters:
The end connector from both 40cm tapes, and the two 'collar' Hoops all connect to a 4-way splitter

The connectors from the Hoops on the waist and the end of the angel hair wire all connect up to a 4-way splitter

The 4-way splitters then connect up to the 2-way splitter and that connects to the driver - simple! 😉

Its not complicated or fiddly - we've just given all those details if you want to plan your costume before you buy the set - feel free to message us if you have any questions.

The whole kit is ready to use - just plug and play!

We have some crazy glowing masks & glasses that go well with this kit - take a look!

- - - - - - - - - - - -

This El Tape comes with a standard connector so simply plugs into any EL driver - this makes it easy to change between coloured wire on one inverter

By using splitters you can also connect different strands to the same driver.

Splitter for 2.1mm/5.5mm 12V LED power supply - use 1 power supply

Here we have splitters for a 2.1mm/5.5mm 12v LED power supply.

This is extremely useful if you have multiple LED emitters, light sources or drivers that you want to run off a single power supply.

The total length of the splitter is 400mm with 190mm before the split.

These splitters are available in:

2 way (useful for powering 2 x LED emitters from 1 x power supply),

3 way (useful for powering 3 x LED emitters from 1 x power supply),

4 way (for powering 4 x LED emitters from 1 x power supply),

5 way (for powering 5 x LED light sources from 1 x power supply),

6 way (for powering 6 x LED light sources from 1 x power supply) and

8 way (for powering 8 x LED light sources from 1 x power supply).

Please select your preferred option from the drop down menu.

Feel free to message us with any questions.

Splitter For 2.1mm/5.5mm 12v power supply

This is a 2 Way 12v Splitter for a 2.1mm/5.5mm 12v Input

This is useful if you have two 12v Drivers that you want to power from a single power input.

These connectors are suggested to be used with our adaptable drivers

If you have never seen EL wire have a look at my other items - it is basically a thin cool glowing neon wire

EL wire has loads of uses

This neon wire looks amazing when decorating the interior or exterior of cars, can be used inside and outside of the home and can even be threaded into clothes and hats.

If you have not seen it before it is like a really long glow stick that lasts around 5,000 hours

We're sure you will be amazed - feel free to message us with any questions you may have.