Basic EL Wire Set = 3 x 1 metre EL Wire + Driver

3 x 1 Metre of EL Wire, Splitter and Portable Driver for up to 5 metres of EL Wire.

This listing is for:

1) 3 x 1 metre of high quality (3.2mm) Electroluminescent Wire
2) 2 x AA portable Driver (with Flash)
3) Standard 3 way Splitter

The splitter lets you have 3 x 1 metre lengths of EL Wire attached to one driver/inverter - This gives you greater control and flexibility in the design of your costume.

4) 30 x Clear Hoops to make it easy to attach the EL Wire to the costume and also make it removable so you can put it through the washing machine

The EL Wire can be any combination of these colours:

Light Blue, Purple, Deep Blue, Pink, Red, Orange, Yellow, Lime Green, Turquoise-Green and White

The 3.2mm diameter EL Wire is one of our brightest!

To make it easier to design your outfit, below are the dimensions of the inverters and lengths of connecting wires - there are also tips on how to create your costume.

POWER PACK / INVERTER (Driver)

The Power Pack takes 2 x AA batteries and has a built-in voltage inverter that 'inverts' the 3Volts from the batteries up to the 100Volts needed to make the EL Wire glow.

The power pack/inverter dimensions are: 9cm x 3.2cm x 2cm

It has the following controls: On / Flash / Strobe / Off

It has an 8cm wire coming out of it that leads to the...

SPLITTER: The Splitter is 40cm long in total; it is 20cm of wire which then splits into 3 separate strands which are all 20cm long and lead to the...

EL WIRE

There is then another 20-25cm from the connector until the actual glowing start of EL Wire - then there are 3 x 1 metre lengths of gorgeous glowing wire!

Its not complicated or fiddly

This set can turn some clothing into a Tron fancy dress in many ways:

1 metre goes down each arm and

1 metre for the front of the costume

1 metre can go across the back and part way down the arm

1 metre to make a helmet

1 metre for the front of the costume

The whole kit is ready to use - just plug and play!

We have some crazy glowing masks & glasses that go well with this kit - take a look!

EL Panel - 2.4cm x 4.5cm

These tiny EL Panels are really handy and can have so many uses.

They run off any EL Driver and you can 'daisy chain' splitters to have as many as you want lit up.

The item we offer to you is a versatile 2.4cm wide and 4.5cm long Electroluminescent Panel.

This panel comes with 10.5cm's wire lead and 9cm's of super thin FFC tape that's even thinner that the panel for great flexibility.

With a driver, these glow very brightly making them ideal for the eye piece in masks.

The panel itself is less than half a millimetre thick but is not see-through.

White, Light Blue, Red or Green

EL Tape is an incredibly versatile material it can be bent and wrapped around things.

It can even have holes and shapes punched into it and be cut to your chosen shape.

All our EL Wire and EL Tape has connectors attached so (with the right driver) it is just plug and play

Standard EL Tape with wires and connector

We have EL Panels and EL Tape in all sorts of shapes and sizes

Including animated and sound activated moving panels!

EL Panel - 3cm x 5cm

These tiny EL Panels are really handy and can have so many uses. They run off any EL Driver and you can 'daisy chain' Splitters to have as many as you want lit up.

The item we offer to you is a versatile 3cm wide and 5cm long Electroluminescent Panel.

With a Driver, these glow very brightly making them ideal for the eye pieces in masks.

The panel itself is less than half a millimetre thick but is not see-through.

The Panels are £2.99 each

In the drop down menu you can choose to have:

Single 3cm x 5cm EL Panels

2 x Panels plus a 2 Way Splitter

2 x Panels plus a 2 Way Splitter and a 2xAA battery operated Driver / Inverter

4 x Panels plus a 4 Way Splitter

Or 4 x Panels, plus a 4 Way Splitter and a 2xAA battery operated Driver / Inverter.

Other inverters, EL Panels, EL Tapes and EL Wire are available in our online store.

Or feel free to contact us if you have any questions.

The 3cm x 5cm are currently available in these colours:

Light Blue (Tron Blue), Red, Pink, Deep Pink, White, Grass Green and Deep Blue

EL Tape is an incredibly versatile material it can be bent and wrapped around things and can even have holes and shapes punched into it and be cut to your chosen shapes.

All our EL Wire and EL Tape has connectors already attached so, (with the right Driver), it is just plug and play

Standard EL Tape with wires and connector

We have EL Panels and EL Tapes in all sorts of shapes and sizes, including animated and sound activated moving EL Panels!

6cm EL Hoop - Glowing Disc of EL Tape

Here we have a glowing hoop of Electro-Luminescent Tape 6cm wide available in Light Blue (Tron Blue), Deep Blue, Pink, Red, Orange, Yellow, Grass Green and White

The hoop needs an Inverter/Driver to make it glow

There is an option within the drop down menu to include a mini 1xAAA or standard 2 x AA battery driver with your purchase.

EL Hoop with some EL Tape in the Tron Style

If you want to link hoops together it is possible to make a single complete cut through the hoop and it will still continue to glow!

The EL Hoops have loads of creative uses but are especially good for making realistic Tron costumes

The EL Hoop is made from EL Tape which is paper thin (300 micron) so it is incredibly versatile and can be easily attached to costume or even a wall for decoration.

We have a whole range of EL Wire, EL Tape and many types of driver/inverters are also available.

If you want any help or advice in planning your EL costume feel free to get in touch.

EL Button - 3cm diameter circle

For Detroit:Become Human, please check out our newest 2cm small EL Hoop.

https://elwirecraft.co.uk/product/2cm-round-hoop-flat-el-panel-detroit-become-human-style/

Here we have a 3cm diameter circle of Electro-Luminescent Tape available in Light Blue (Tron Blue), Pink, Red, Orange,Yellow, Grass Green and White

This EL Button has been designed to help you achieve a realistic Tron costume.

3 EL Buttons in a row

Like all EL Tape and EL Wire, the EL Buttons need an Inverter/Driver to make it glow - you have the option in the drop-down menu, to buy these hoops with a 2 x AA battery Driver - there is a bigger selection in our online store including 'Splitters' so that you could have up to 10 of them attached to a single Driver.

Standard EL Tape with wires and connector

The EL Buttons have loads of other creative uses but are especially good for making realistic Tron costumes

The EL Button is made from EL Tape which is paper thin (300 micron) so it is incredibly versatile and can be easily attached to costume or even a wall for decoration

We have a whole range of EL Wire, EL Tape, EL Panels and many types of Driver/Inverters are also available.

If you want any help or advice in planning your EL costume, please contact us and speak to a member of our team.

EL Tape Tron Identity Disc (14cm diameter)

This is a 14cm diameter Electro-Luminescent circular EL Panel available in Light Blue (Tron Blue), White, Orange, Red and Deep Blue

This EL Disc has been designed to help you achieve a realistic Tron costume by using as an Identity Disc on the back of the costume.

It needs a Driver to make it glow

The 2xAA Driver can light up this EL Disc.

The Powerful Portable 8xAA Driver will power this EL Disc PLUS another 2 pieces of 2cm x 1m EL Tapes.

Other Driver/Inverters and glowing EL parts of Tron costumes are available in our online store.

A White El Disc

All our El Wire, Tapes and Panels come with wires and connectors already attached.

Standard EL Tape with wires and connector

These EL Discs have loads of other creative uses but are especially good for making realistic Tron costumes.

The EL Disc is made from EL Panel which is paper thin (300 micron) so it is incredibly versatile and can be easily attached to costumes or even a wall for decoration.

We have a whole range of EL Wire, EL Tape s and EL Panels and many types of Drivers / Inverters are also available.

If you would like any help or advice in planning your EL costume, please email us.

EL Tape Tron Sacral Piece

This EL Tape has been designed to be worn down the base of the spine for a realistic Tron Costume.

The beautiful 'Tron Circuit' style can be worn on any part of the body to create an amazing effect.

The piece is 18cm tall and 9cm wide and available in these colours:

Light Blue (Tron Blue), White and Orange

The EL Tape needs a Driver to make it glow

The Powerful Portable 8xAA Driver can power up to ten of these pieces.

Other Driver/Inverters and glowing EL parts of Tron costumes are available in our store.

All our El Wire and Tape comes with wires and connectors attached

Standard EL Tape with wires and connector

This EL Panel has loads of other creative uses but are especially good for making realistic Tron costumes

It is made from EL Tape which is paper thin (300 micron) so it is incredibly versatile and can be easily attached to costume or even a wall for decoration

We have a whole range of EL Wire, EL Tape and many types of driver/inverters are also available.

If you want any help or advice in planning your EL costume feel free to get in touch.

EL Tape TRON SET = 2 x 25cm Tape + EL Hoops + Driver

This amazing kit contains just what you need for a great glowing Tron costume:

1) 2 pieces of 2cm x 25cm EL Tape

2) 2 pieces 6cm EL Hoops

3) 4 Way Black Splitter

4) Powerful portable Driver/Inverter powered by 8xAA batteries (not supplied) or rechargeable Li-ion battery.

5) It also comes with just over 50cm of Velcro - sticky on one side and sewable on the other to help you attach the El Tape and EL Hoops to a costume.

The EL Tape and EL Hoops can be any combination of these colours:

Light Blue (Tron Blue), Deep Blue, Pink, Green, Orange, and White

The whole kit is ready to use - add batteries and plug and play!

Dimensions of the products:

If you are making a costume, it is a good idea to plan it out properly.

So here are the dimensions of all the parts plus lengths of wire between them:

THE POWER PACK

Takes 8 x AA batteries (not supplied) and is 6.5cm x 6cm x 3cm

it has a 65cm thin power wire coming out of it that leads to the...

DRIVER

The driver is 6cm x 4cm x 4cm

It has the controls on it - Off, Flashing or On

It has a 55cm wire coming out of it that leads to the...

SPLITTER

The 4 Way Splitter is 40cm long in total,

it is 20cm of wire which then splits into 4 separate strands which are all 20cm long and lead to the...

EL TAPE

The EL Tape has a 20cm wire on it before 25cm of glorious glowing EL Tape

The tape is just 350 microns thick - that is 1/3rd of a millimetre!

Sticky back Velcro is supplied that is the exact width of the EL Tape - be careful putting it on as that glue is VERY sticky

You must sew the other part of the Velcro onto the costume making it very convenient to attach and remove

Of course, you don't need to use the Velcro and fix it any way you choose

EL HOOPS

Two channels of the Splitter lead to these glowing discs of EL Tape that give your costume and authentic Tron look

Its not complicated or fiddly - we've just given all those details if you want to plan your costume before you buy the set - feel free to message us if you have any questions.

OR CONTACT US IF YOU WANT ADVICE PLANNING YOUR SET

We have some crazy glowing masks & glasses that go well with this kit - take a look!

This EL Tape comes with a standard connector so simply plugs into any EL inverter - this makes it easy to change between coloured wire on one inverter.

By using splitters you can also connect different strands to the same Inverter / Driver

EL Tape Tron Boot Piece

This EL Tape has been designed to be worn down the ankle and wrap around a boot for a realistic Tron Costume.

The beautiful 'Tron Circuit' style can be worn on any part of the body to create an amazing effect.

The piece is 32cm high and 22cm wide and is currently only available in: Orange

It needs a Driver to make it glow

The Powerful Portable 8xAA Driver can power up to four of these pieces

All our El Wire and Tape comes with wires and connectors attached

Standard EL Tape with wires and connector

This EL Panel has loads of other creative uses but are especially good for making realistic Tron costumes.

It is made from EL Tape which is paper thin (300 micron) so it is incredibly versatile and can be easily attached to costume or even a wall for decoration

We have a whole range of EL Wire, EL Tape and many types of driver/inverters are also available.

If you want any help or advice in planning your EL costume feel free to get in touch.

EL Tape TRON SET = 2 x 40cm EL Tape + EL Hoops + EL Wire + Driver

This amazing item consists of:

1) 2 pieces of 2cm x 40cm EL Tape,

2) 4 x 6cm EL Hoops,

3) 2 pieces of 1m x 1.5mm EL Wire,

4) 2 x 4-way splitters and a 2-way splitter,

5) and a powerful portable Driver/Inverter with either an 8xAA battery box (batteries not supplied) or a 3000mAh rechargeable Li-ion battery (only available in the UK due to airmail postal restrictions),

6) It also comes with 80cm of Velcro - sticky on one side and sewable on the other to help you attach the tape and hoops to a costume

The EL Wire can be any combination of these colours:

Light Blue (Tron Blue), White and Orange

The whole kit is ready to use - just plug and play!

Dimensions of the products:

If you are making a costume, it is a good idea to plan it out properly.

For this set, the driver is very powerful and comes with a separate power pack.

So here are the dimensions of all the parts plus lengths of wire between them.

Feel free to message us if you have any questions.

THE POWER PACK

Takes 8 x AA batteries (not supplied) and is 6.5cm x 6cm x 3cm

it has a 65cm thin power wire coming out of it that leads to the...

DRIVER

The driver is 6cm x 4cm x 4cm

It has the controls on it - Off, Flashing or On

It has a 55cm wire coming out of it that leads to the...

SPLITTER

The Splitter is 40cm long in total,

it is 20cm of wire which then splits into 3 separate strands which are all 20cm long - 2 of them then lead to...

2 x EL TAPE

The EL Tape has a metre of wire on it before the 2cm X 40cm super-bright glow of the EL Tape

The tape is just 350 microns thick - that is 1/3rd of a millimetre!

Sticky back Velcro is supplied that is the exact width of the EL Tape - be careful putting it on as that glue is VERY sticky

You must sew the other part of the Velcro onto the costume making it very convenient to attach and remove

Of course, you don't need to use the Velcro and can fix it any way you choose

EL HOOPS

Two channels of the splitter lead to these glowing discs of EL Tape onto the shoulders

These 6cm diameter hoops also come with sticky back Velcro discs to attach them to your costume

EL WIRE

This thin but very bright EL Wire gives an amazing effect as it runs from the hoop near the collar, over the shoulder, down the back and round the waist where it meets the other EL Hoop

SPLITTERS

This is how we recommend using the splitters:
The end connector from both 40cm tapes, and the two 'collar' Hoops all connect to a 4-way splitter

The connectors from the Hoops on the waist and the end of the angel hair wire all connect up to a 4-way splitter

The 4-way splitters then connect up to the 2-way splitter and that connects to the driver - simple! 😉

Its not complicated or fiddly - we've just given all those details if you want to plan your costume before you buy the set - feel free to message us if you have any questions.

The whole kit is ready to use - just plug and play!

We have some crazy glowing masks & glasses that go well with this kit - take a look!

- - - - - - - - - - - -

This El Tape comes with a standard connector so simply plugs into any EL driver - this makes it easy to change between coloured wire on one inverter

By using splitters you can also connect different strands to the same driver.

T-Square Shape for Rinzler

This T Square EL Panel is ideal for a Tron Rinzler Costume

The T square glows brightly and is 8cm long and 5cm tall

Each of the cells are 1.7 cm square

The shape is available in White or Orange and has been designed to help you achieve a realistic Tron costume.

As you can see in the picture below it is perfectly suited for use with straight EL Tape and the EL Hoops

Like all EL Tape and EL Wire the EL T- Square needs an EL Driver to make it glow - there is a selection available

EL Tape, Curve and Hoop in the Tron Style

All our El Wire and Tape comes with wires and connectors attached

Like all EL Tape and EL Wire the EL Curve needs an EL Driver to make it glow - there is a selection available in our online store.

On this EL Curve, the wires are connected in the middle of the bend so either end can be cut to a shape you need.

Standard EL Tape with wires and connector

A wide selection of other EL Tape, EL Wire, Sequencers, Drivers and helpful EL accessories are available from our online store.

The EL Curves have loads of other creative uses but are especially good for making realistic Tron costumes.

The EL Curve is made from EL Tape which is paper thin (300 micron) so it is incredibly versatile and can be easily attached to a costume or even a wall for decoration.

We have a whole range of EL Wire, EL Tape and many types of driver/inverters are also available.

If you want any help or advice in planning your EL costume feel free to get in touch.

LEG Pieces for Tron Replica Set

This Tron Leg Set contains:

1) Two pieces of replica shaped EL Tape for the boots of a Tron Costume - Sam Flynn, Rinzler or Quorra

2) Two pieces of shaped and angled EL Tape to go round the knees

3) Two pieces of sacral shaped EL Panel to go at the lower back

4) Two pieces of 2cm x 25cm EL Tape

5) A Powerful Driver with 8xAA Battery Box

6) A 2 Way Splitter, A 3 Way Splitter and 2 x 'Short, Medium and Long' Splitters

6) 1.5 metre of Velcro - with sticky hoop and sewable loop to make it easy to attach to a costume and have it removable for washing.

The Set is available in the following colours:

Orange or Light Blue

The whole kit is ready to use - just plug and play!

Dimensions of the products:

If you are making a costume, it is a good idea to plan it out properly. Feel free to email us with any questions you may have.

For this set, the Driver / Inverter is very powerful and comes with a separate power pack

So here are the dimensions of all the parts plus lengths of wire between them.

THE POWER PACK

Takes 8 x AA batteries (not supplied) and is 12.7cm x 7.2cm x 1.9cm

it has a 21cm thin power wire coming out of it that leads to the...

DRIVER

The Driver is 6cm x 4cm x 4cm

It has the controls on it - Off, Flashing or On

It has a 55cm wire coming out of it that leads to the...

SPLITTER

The Splitter is 40cm long in total,

it is 20cm of wire which then splits into separate strands which are all 20cm long.

A 3 Way Splitter attaches to the Driver

One of these channels has a 2 Way Splitter attached that runs round the back to clip into the pair of EL Sacral pieces

The other two channels have a special '3 Way Small Midi and Long' Splitter attached to them that run down each leg

These SML splitters have:

one Short channel that plugs to the 25cm Tape.

Then the Middle channel plugs into the Knee Joint section

The Long channel goes down to the Shin to plug into the Double Hoop

The three pieces of EL Tape that run down the leg are:

1) SHIN

This 15cm Double Hoop is designed to run from your shin to the ankle to give a great finishing touch to any Tron costume (these are also available for other parts of your Tron costume in our store

2) KNEE JOINT

Running up from the boot piece, this piece of EL Tape takes an angle round the knee, exactly as in the original costumes

This has been made to the largest size and will not fit everyone so it has been designed so you can just snip it down to the right size for you

That's right, it really is as easy as just cutting the unwanted part off either or both ends (sealing the cut with sellotape, glue or clear nail varnish is highly recommended)

3) 2cm x 25cm EL Tape

Another piece that can be cut to size is this straight piece of EL Tape that runs from the Knee Joint up to join the top half of the costume

Coming off the two-way splitter at the back of the costume:

4) EL SACRAL

This pair of pieces sits at the base of the spine and looks pretty awesome

The EL Tape is just 350 microns thick - that is 1/3rd of a millimetre!

Sticky back Velcro is supplied that is the exact width of the EL Tape - be careful putting it on as that glue is VERY sticky

You must sew the other part of the Velcro onto the costume making it very convenient to attach and remove

Of course, you don't need to use the Velcro, fix it any way you choose.

Its not complicated or fiddly.

The whole kit is ready to use - just plug and play!

We have some crazy glowing masks & glasses that go well with this kit - take a look!

A wide selection of other EL Tape, EL Wire, Sequencers, Drivers and helpful EL accessories are available from this store

Sam Flynn Tron - FULL Replica EL Panel Costume - Torso, Legs and Driver

Finally, we can get this full Tron Set running from a single portable Driver.

This Tron Full EL Panel Set in Light Blue (Tron Blue) is a combination of the Flynn Replica Torso Set and the Tron Leg Set

There are details of how we suggest the layout for replica below:

It goes on a bit, but that is to help you get it exactly right. It is all actually very easy to use and just clips together.

The guy on the right of the picture below has used the set to make a copy of the Sam Flynn costume (please note we do not supply the disc he is holding)

The girl on the left has created her own Tron inspired design with the same set. The design is completely flexible if you want to use it that way.

We suggest finding a comfortable garment to attach it to.

All these Tron Sets comes with sewable Velcro to go on the costume and sticky Velcro that goes on the back of the panel making it very easy to attach to any clothing

This is the full list of what is enclosed in this set and our suggested layout:

Torso Pieces

1) Two pieces of replica shaped EL Tape for the front of a Sam Flynn Costume - a Left and a Right

2) A single 1.5cm x 15cm EL Tape for the glowing mid line

3) A 14cm EL Identity Disc for the back of the costume

4) Two pieces of 2cm x 40cm Curved EL Tape for the back of a Tron Costume - It is curved to go round the ID Disc and over the shoulder

5) Two pieces of 1.5cm x 15cm EL Tape for the top of the arms of the Tron costume

6) 3 x 3 Way Splitters, a 2 x 2 Way Splitters and a 50cm long Extender to make it a simple 'plug and play' but also with plenty of room for the wire to stretch around the costume

Leg Pieces

1) Two pieces of replica shaped EL Tape for the boots of a Tron Costume - Sam Flynn, Rinzler or Quorra

2) Two pieces of shaped and angled EL Tape to go round the knees

3) Two pieces of sacral shaped EL Panel to go at the lower back

4) Two pieces of 2cm x 25cm EL Tape

5) A 2 Way Splitter, A 3 Way Splitter and 2 x 'Short, Medium and Long' Splitters

You will also get

1) 2 metres of Velcro - with sticky hoop and sewable loop to make it easy to attach the set to a costume and be removable so it can be washed.

2) A single Powerful 8x AAbattery (batteries not supplied) inverter to drive BOTH SETS

The whole kit is ready to use - just plug and play!

Dimensions of the products:

If you are making a costume, it is a good idea to plan it out properly.

The Torso Section

For this set, the driver/inverter is very powerful and comes with a separate power pack

So here are the dimensions of all the parts plus lengths of wire between them.

Feel free to message us if you have any questions.

THE POWER PACK:

Takes 8xAA batteries (not supplied) and is 12.7cm x 7.2cm x 1.9cm and has a 65cm thin power wire coming out of it that leads to the...

INVERTER / DRIVER:

The inverter is 6cm x 4cm x 4cm

It has the controls on it - Off, Flashing or On

It has a 55cm wire coming out of it that leads to the...

SPLITTER:

The Splitter is 40cm long in total and it is 20cm of wire which then splits into 3 separate strands which are all 20cm long - 2 of them then lead to...

Left and Right Flynn Replica EL Tapes:

The EL Tape is 30cm from top to tail with the stick and hoop that comes in near the shoulder adding another 8cm

The tape is just 350 microns thick - 1/3rd of a millimetre.

Sticky back Velcro is supplied that is the exact width of the EL Tape - be careful putting it on as the glue is VERY sticky

You will need to sew the other part of the Velcro onto the costume making it very convenient to attach and remove

You don't need to use the Velcro and can fix it any way you choose.

Mid-Line

Sam Flynn has a small line of light that runs down the middle of his chest. This is lit by the 1.5cm X15cm EL Tape provided. This tape can be easily cut to shape if you prefer it smaller

EL Identity Disc

This Large El Hoop is 14cm in diameter, there are two thin EL Tapes running in concentric circles and the inner diameter is just over 9cm across

2cm x 40cm Curved Outline

The EL Tape is curved so is 37 cm from top to tail - it has been designed to go on the back round the ID disc and curve over the shoulder

EL Tape for the Arms: 2pcs of 1.5cm x 15cm EL Tape, one for each arm

SPLITTERS:

This is how we recommend using the Splitters

A 2 Way Splitter coming straight from the Inverter - this divides the front and the back:

The First channel goes to a 3 Way Splitter to power the front of the costume - The left and right Flynn Tape plus the mid-line

The Second channel can be fitted with the Extender wire and this will allow it to reach to the back of the costume

A 3 Way Splitter attaches to this:

1 channel does the 1.5cm x 15cm left arm

2nd channel does the left 2cm x 40cm curved outline

The 3rd channel has another 3 Way Splitter on it

1st channel attaches to the ID Disc

2nd channel has the Right 2cm x 40cm curved outline

3rd channel does the 1.5cm x 15cm right arm

Depending on where you have the inverter, you may or may not need the extender wire

The Leg Section

1) Two pieces of replica shaped EL Tape for the boots of a Tron Costume - Sam Flynn, Rinzler or Quorra

2) Two pieces of shaped and angled EL Tape to go round the knees

3) Two pieces of sacral shaped EL Panel to go at the lower back

4) Two pieces of 2cm x 25cm EL Tape

5) A 2 Way Splitter, A 3 Way Splitter and 2 x 'Short, Medium and Long' Splitters

The whole kit is ready to use - just plug and play!

If you are making a costume, it is a good idea to plan it out properly.

For this set, the driver/inverter is very powerful and comes with a separate power pack

So here are the dimensions of all the parts plus lengths of wire between them.

DRIVER

The Torso and Leg set run off the same Driver

SPLITTER

The Splitter is 40cm long in total,

it is 20cm of wire which then splits into separate strands which are all 20cm long.

A 3 Way Splitter attaches to the Driver

One of these channels has a 2 Way Splitter attached that runs round the back to clip into the pair of EL Sacral pieces

The other two channels have a special '3 way Small Midi and Long' splitter attached to them that run down each leg

These SML splitters have:

one Short channel that plugs to the 25cm Tape.

Then the Middle channel plugs into the Knee Joint section

The Long channel goes down to the shin to plug into the Double Hoop

The three pieces of EL Tape that run down the leg are:

1) SHIN

This 15cm Double Hoop is designed to run from your shin to the ankle to give a great finishing touch to any Tron costume (these are also available for other parts of your Tron costume in our store

2) KNEE JOINT

Running up from the boot piece, this piece of EL Tape takes an angle round the knee, exactly as in the original costumes

This has been made to the largest size and will not fit everyone so it has been designed so you can just snip it down to the right size for you

That's right, it really is as easy as just cutting the unwanted part off either or both ends (sealing the cut with sellotape, glue or clear nail varnish is highly recommended)

3) 2cm x 25cm EL Tape

Another piece that can be cut to size is this straight piece of EL Tape that runs from the Knee Joint up to join the top half of the costume

Coming off the two-way splitter at the back of the costume:

4) EL SACRAL

This pair of pieces sits at the base of the spine and looks pretty awesome

The EL Tape is just 350 microns thick - that is 1/3rd of a millimetre!

Sticky back Velcro is supplied that is the exact width of the EL Tape - be careful putting it on as that glue is VERY sticky

You must sew the other part of the Velcro onto the costume making it very convenient to attach and remove

Of course, you don't need to use the Velcro, fix it any way you choose

Its not complicated or fiddly - I've just given all those details if you want to plan your costume before you buy the set - feel free to message us if you have any questions.

The whole kit is ready to use - just plug and play!

OR CONTACT US IF YOU WANT ADVICE PLANNING YOUR SET

We have some crazy glowing masks & glasses that go well with this kit - take a look!

Quorra Replica EL Panel Front + Back + Driver

This listing is for:

1) Two pieces of single EL Hoops to go near each shoulder

2) 1.5cm x 25cm EL Tape to go down the front at one side

3) 2cm x 40cm EL Tape to go down the front at the other side

4) 2cm x 6cm EL Curve to 'tail off' the 40cm EL Tape

5) Two pieces EL Double Hoops for the waist

6) 14cm EL Tape Tron Identity Disc

7) A Powerful 8xAA Battery EL Driver (or rechargeable 3000mAh Li-ion Driver)

8) 5 Way Splitter, 3 Way Splitter, Mini 2 Way Splitter, Mini 3 Way Splitter - these make the whole set a simple 'plug and play'

9) 1 metre of Velcro - with sticky hoop and sewable loop to make it easy to attach the set to a costume and have it removable

The whole kit is ready to use - just plug and play!

Dimensions of the products:

If you are making a costume, it is a good idea to plan it out properly.

For this set, the driver/inverter is very powerful and comes with a separate power pack

So here are the dimensions of all the parts plus lengths of wire between them.

Feel free to message us if you have any questions

THE POWER PACK*

Takes 8 x AA batteries (not supplied) and is 12.7cm x 7.02cm x 1.9cm and has a 19cm thin power wire coming out of it that leads to the Driver

it has a 65cm thin power wire coming out of it that leads to the...

DRIVER

The Driver is 6cm x 4cm x 4cm

It has the controls on it - Off, Flashing or On

It has a 55cm wire coming out of it that leads to the...

SPLITTER

The 5 Way Splitter is 40cm long in total,

it is 20cm of wire which then splits into 5 separate strands which are all 20cm long

1 of them then lead to...

Front Right

A Mini 2 Way splitter plugs into a 6cm EL Hoop and a thin 1.5cm x 25cm EL Tape

Sticky back Velcro is supplied that is the exact width of the EL Tape - be careful putting it on as that glue is VERY sticky

You must sew the other part of the Velcro onto the costume making it very convenient to attach and remove

Of course, you don't need to use the Velcro and can fix it any way you choose to.

Front Left

Here a Mini 3 Way splitter is plugged into a 6cm EL Hoop, a long 2cm x 40cm EL Tape and a 6cm EL Curve to tail off the end of the EL Tape

Two more of the channels off the main 5 Way Splitter go to...

Double Hoops

These two Double Hoop EL Shapes curve round either side of the waist

Another channel, off the main 5 Way Splitter goes to the back of the costume to the...

EL Identity Disc

This Large EL Hoop is 14cm in diameter, there are two thin EL Tapes running in concentric circles and the inner diameter is just over 9cm across

SPLITTERS

This is how we recommend using the Splitters:

A 5 Way Splitter coming straight from the Driver - for the left side, right side, 2 x Double Hoops and ID disc

* Instead of 8 x AA battery pack this whole unit can be powered by a small rechargeable Li-ion battery

The 3000mAh battery is as powerful as 8 x AA batteries but weighs only 172g and is 7.3cm x 5.6cm x 2.2cm

It comes with an Intelligent Charger with UK plug

The whole kit is ready to use - just plug and play!

We have some crazy glowing masks & glasses that go well with this kit - have a look!

Siren Gem Replica EL Panel Set, Torso + Legs + Driver

This listing is for:

1) Four pieces of Angular EL Tape for the body of a Gem Costume

2) A single 1.5cm x 15cm EL Tape that can be easily snipped to length - for the glowing mid line

3) Two pieces of 2cm x 40cm Curved EL Tape for the back of a Tron Costume - It is curved to go round the ID Disc and over the shoulder

4) 1 x 14cm Tron Identity Disc, made of EL tape.

5) A Powerful 8 x AA battery EL Driver or rechargeable 3000mAh Li-ion Driver.

6) 1 x 4-way splitters, a 3-way splitter, a mini 3-way splitter and 2 x 50cm extender for the leg parts - these make the whole set a simple 'plug and play'

7) 1.5metres of Velcro - with sticky hoop and sewable loop to make it easy to attach the set to a costume and have it removable

This set is only available in Light Blue (Tron Blue)

The whole kit is ready to use - just plug and play!

Dimensions of the products:

If you are making a costume, it is a good idea to plan it out properly.

For this set, the driver/inverter is very powerful and comes with a separate power pack

So here are the dimensions of all the parts plus lengths of wire between them.

Feel free to message us if you have any questions

THE POWER PACK*

Takes 8 x AA batteries (not supplied) and is 12.7cm x 7.02cm x 1.9cm and has a 19cm thin power wire coming out of it that leads to the driver

DRIVER

The driver is 8cm x 5cm x 3.2cm

It has the controls on it - Off, Flashing or On

It has a 55cm wire coming out of it that leads to the...

SPLITTER

The 4- way Splitter is 40cm long in total,

it is 20cm of wire which then splits into 4 separate strands which are all 20cm long - 1 of them then lead to...

Gem Front

This part has its own mini-3way splitter attached to two of the 2cm x 40cm Curved EL Tape and the 1.5cm x 15cm mid line Piece

Sticky back Velcro is supplied that is the exact width of the EL Tape - be careful putting it on as that glue is VERY sticky

You must sew the other part of the Velcro onto the costume making it very convenient to attach and remove

Of course, you don't need to use the Velcro and can fix it any way you choose

Another channel, off the main 4-way splitter, goes to the back of the costume

Plug the other 3-way splitter into the 4-way splitter and those three channels go off too...

EL Identity Disc

This Large El Hoop is 14cm in diameter, there are two thin EL Tapes running in concentric circles and the inner diameter is just over 9cm across

and...

2cm x 40cm Curved Outline

The EL Tape is curved so is 37 cm from top to tail - it has been designed to go on the back round the ID disc and curve over the shoulder

The other two channels off the main 4-way splitter are for the leg pieces

a 50cm extender wire plugs into both of these to take the power too...

Gem Leg Pieces

Each leg has a 40 cm angled EL Tape to run down to the knee

SPLITTERS

This is how we recommend using the splitters

A 4-way splitter coming straight from the driver - for the front, the back and each leg

Depending on where you have the inverter, you may or may not need both extender wires

*Instead of 8 x AA battery pack this whole unit can be powered by a small rechargeable Li-ion battery

The 3000mAh battery is as powerful as 8 x AA batteries but weighs only 172g and is 7.3cm x 5.6cm x 2.2cm and comes with an Intelligent Charger

Its not complicated or fiddly - I've just given all those details if you want to plan your costume before you buy the set - feel free to message me if you have any questions

The whole kit is ready to use - just plug and play!

OR CONTACT US IF YOU WANT ADVICE PLANNING YOUR SET

We have some crazy glowing masks & glasses that go well with this kit - take a look!

Tron Rinzler - Basic EL Panel Set

Here we have a really effective 'plug and play' EL Tape, splitters and EL Driver.

It still needs to be attached to your own costume.

With this set you get:

1) An Orange Rinzler T-Square

2) Two EL Hoops for the front of the costume

3) A Mini 1xAAA EL Driver

4) A 3-way splitter

5) 20cm of Velcro - with sticky hoop and sewable loop to make it easy to attach the set to a costume and have it removable.

This set is only available in ORANGE

The whole kit is ready to use - just plug and play!

If you are making a costume, it is a good idea to plan it out properly.

Feel free to message us if you have any questions.

So here are the dimensions of all the parts plus lengths of wire between them.

MINI DRIVER

The driver is 5cm x 2.5cm x 1.5cm

It has a switch on it - Off, On Continuous or Flashing and has a 10cm wire coming out of it that leads to the...

SPLITTER

The Splitter is 40cm long in total, 20cm of wire which then splits into 3 separate strands which are each 20cm long - 1 of them then lead to...

The Rinzler T-Square

This sits at the front of the chest and is 8cm wide and 4 cm long. The tape is just 350 microns thick - that is 1/3rd of a millimetre!

Sticky back Velcro is supplied to stick to the back of these EL Shapes - be careful putting it on as that glue is VERY sticky

You can then sew the other part of the Velcro onto the costume making it very convenient to attach and remove

Of course, you don't need to use the Velcro and can fix it any way you choose

EL Hoops

These hoops can be placed anywhere on the costume to give a great Tron effect

The whole kit is ready to use - just plug and play!

- - - - - - - - - - - -

This EL Tape comes with a standard connector so simply plugs into any EL driver - this makes it easy to change between coloured wire on one driver.

By using splitters you can also connect different strands to the same driver.

We have some crazy glowing masks & glasses that go well with this kit - take a look!