Basic Tron Set = 2 x 1m of EL Wire + 2 x EL Tape Hoops + Driver

With this set you get:

1) 2 pieces of 1 metre high quality (3.2mm) Electroluminescent Wire

2) 2 x 6cm diameter EL Tape Hoops.

3) A decent 4 x AAA battery Driver/Inverter with on/off switch plus 4 modes including continuous ON, Strobe, Slow flash and Fast flash

4) 1 x 4 way splitter. The splitter lets you have 2 x 1 metre lengths of EL Wire and the 2 x 6cm hoops attached to one driver/inverter - This gives you greater control and flexibility in the designs of your Tron costume

5) 10cm of Velcro - sticky on one side and sewable on the other to help you attach the EL Hoops to a costume.

6) 10 clear plastic hoops - to sew on to your costume which you then feed the EL Wire through.

The EL Wire can be any combination of these colours:

Light Blue (Tron Blue), White, Red, Orange, Purple, Pink and Yellow

To make it easier to design your outfit, below are the dimensions of the inverters and lengths of connecting wires - there is also tips on how to create your costume

DRIVER/INVERTER

The Power Pack takes 4 x AAA batteries and has a built-in voltage inverter that 'inverts' the 6 Volts from the batteries up to the 100 Volts needed to make the EL Wire glow

The power pack/inverter is 8.5cm x 5cm x 2cm

It has an On/Off switch - plus a mode button for the 4 Modes: Continuous, Strobe, Fast flash and Slow flash

It has an 8cm wire coming out of it that leads to the...

SPLITTER

The Splitter is 40cm long in total,

it is 20cm of wire which then splits into 4 separate strands which are all 20cm long and lead to the...

EL WIRE

There is then another 20-25cm from the connector until the actual glowing start of EL Wire - then there is 2 X 1metres of gorgeous glowing wire!

These are long enough to run up the body and down the arm

EL HOOPS

The other part of the splitter runs to two 6cm diameter EL Hoops that make any Tron costume look amazing

Its not complicated or fiddly - I've just given all those details if you want to plan your costume before you buy the set

The whole kit is ready to use - just plug and play!

OR FEEL FREE TO CONTACT US IF YOU WANT HELP WITH YOUR EL PROJECT

We have some crazy glowing masks & glasses that go well with this kit - take a look!

EL Button - 3cm diameter circle

For Detroit:Become Human, please check out our newest 2cm small EL Hoop.

https://elwirecraft.co.uk/product/2cm-round-hoop-flat-el-panel-detroit-become-human-style/

Here we have a 3cm diameter circle of Electro-Luminescent Tape available in Light Blue (Tron Blue), Pink, Red, Orange,Yellow, Grass Green and White

This EL Button has been designed to help you achieve a realistic Tron costume.

3 EL Buttons in a row

Like all EL Tape and EL Wire, the EL Buttons need an Inverter/Driver to make it glow - you have the option in the drop-down menu, to buy these hoops with a 2 x AA battery Driver - there is a bigger selection in our online store including 'Splitters' so that you could have up to 10 of them attached to a single Driver.

Standard EL Tape with wires and connector

The EL Buttons have loads of other creative uses but are especially good for making realistic Tron costumes

The EL Button is made from EL Tape which is paper thin (300 micron) so it is incredibly versatile and can be easily attached to costume or even a wall for decoration

We have a whole range of EL Wire, EL Tape, EL Panels and many types of Driver/Inverters are also available.

If you want any help or advice in planning your EL costume, please contact us and speak to a member of our team.

EL Tape TRON SET = 2 x 40cm EL Tape + EL Hoops + EL Wire + Driver

This amazing item consists of:

1) 2 pieces of 2cm x 40cm EL Tape,

2) 4 x 6cm EL Hoops,

3) 2 pieces of 1m x 1.5mm EL Wire,

4) 2 x 4-way splitters and a 2-way splitter,

5) and a powerful portable Driver/Inverter with either an 8xAA battery box (batteries not supplied) or a 3000mAh rechargeable Li-ion battery (only available in the UK due to airmail postal restrictions),

6) It also comes with 80cm of Velcro - sticky on one side and sewable on the other to help you attach the tape and hoops to a costume

The EL Wire can be any combination of these colours:

Light Blue (Tron Blue), White and Orange

The whole kit is ready to use - just plug and play!

Dimensions of the products:

If you are making a costume, it is a good idea to plan it out properly.

For this set, the driver is very powerful and comes with a separate power pack.

So here are the dimensions of all the parts plus lengths of wire between them.

Feel free to message us if you have any questions.

THE POWER PACK

Takes 8 x AA batteries (not supplied) and is 6.5cm x 6cm x 3cm

it has a 65cm thin power wire coming out of it that leads to the...

DRIVER

The driver is 6cm x 4cm x 4cm

It has the controls on it - Off, Flashing or On

It has a 55cm wire coming out of it that leads to the...

SPLITTER

The Splitter is 40cm long in total,

it is 20cm of wire which then splits into 3 separate strands which are all 20cm long - 2 of them then lead to...

2 x EL TAPE

The EL Tape has a metre of wire on it before the 2cm X 40cm super-bright glow of the EL Tape

The tape is just 350 microns thick - that is 1/3rd of a millimetre!

Sticky back Velcro is supplied that is the exact width of the EL Tape - be careful putting it on as that glue is VERY sticky

You must sew the other part of the Velcro onto the costume making it very convenient to attach and remove

Of course, you don't need to use the Velcro and can fix it any way you choose

EL HOOPS

Two channels of the splitter lead to these glowing discs of EL Tape onto the shoulders

These 6cm diameter hoops also come with sticky back Velcro discs to attach them to your costume

EL WIRE

This thin but very bright EL Wire gives an amazing effect as it runs from the hoop near the collar, over the shoulder, down the back and round the waist where it meets the other EL Hoop

SPLITTERS

This is how we recommend using the splitters:
The end connector from both 40cm tapes, and the two 'collar' Hoops all connect to a 4-way splitter

The connectors from the Hoops on the waist and the end of the angel hair wire all connect up to a 4-way splitter

The 4-way splitters then connect up to the 2-way splitter and that connects to the driver - simple! 😉

Its not complicated or fiddly - we've just given all those details if you want to plan your costume before you buy the set - feel free to message us if you have any questions.

The whole kit is ready to use - just plug and play!

We have some crazy glowing masks & glasses that go well with this kit - take a look!

- - - - - - - - - - - -

This El Tape comes with a standard connector so simply plugs into any EL driver - this makes it easy to change between coloured wire on one inverter

By using splitters you can also connect different strands to the same driver.

LEG Pieces for Tron Replica Set

This Tron Leg Set contains:

1) Two pieces of replica shaped EL Tape for the boots of a Tron Costume - Sam Flynn, Rinzler or Quorra

2) Two pieces of shaped and angled EL Tape to go round the knees

3) Two pieces of sacral shaped EL Panel to go at the lower back

4) Two pieces of 2cm x 25cm EL Tape

5) A Powerful Driver with 8xAA Battery Box

6) A 2 Way Splitter, A 3 Way Splitter and 2 x 'Short, Medium and Long' Splitters

6) 1.5 metre of Velcro - with sticky hoop and sewable loop to make it easy to attach to a costume and have it removable for washing.

The Set is available in the following colours:

Orange or Light Blue

The whole kit is ready to use - just plug and play!

Dimensions of the products:

If you are making a costume, it is a good idea to plan it out properly. Feel free to email us with any questions you may have.

For this set, the Driver / Inverter is very powerful and comes with a separate power pack

So here are the dimensions of all the parts plus lengths of wire between them.

THE POWER PACK

Takes 8 x AA batteries (not supplied) and is 12.7cm x 7.2cm x 1.9cm

it has a 21cm thin power wire coming out of it that leads to the...

DRIVER

The Driver is 6cm x 4cm x 4cm

It has the controls on it - Off, Flashing or On

It has a 55cm wire coming out of it that leads to the...

SPLITTER

The Splitter is 40cm long in total,

it is 20cm of wire which then splits into separate strands which are all 20cm long.

A 3 Way Splitter attaches to the Driver

One of these channels has a 2 Way Splitter attached that runs round the back to clip into the pair of EL Sacral pieces

The other two channels have a special '3 Way Small Midi and Long' Splitter attached to them that run down each leg

These SML splitters have:

one Short channel that plugs to the 25cm Tape.

Then the Middle channel plugs into the Knee Joint section

The Long channel goes down to the Shin to plug into the Double Hoop

The three pieces of EL Tape that run down the leg are:

1) SHIN

This 15cm Double Hoop is designed to run from your shin to the ankle to give a great finishing touch to any Tron costume (these are also available for other parts of your Tron costume in our store

2) KNEE JOINT

Running up from the boot piece, this piece of EL Tape takes an angle round the knee, exactly as in the original costumes

This has been made to the largest size and will not fit everyone so it has been designed so you can just snip it down to the right size for you

That's right, it really is as easy as just cutting the unwanted part off either or both ends (sealing the cut with sellotape, glue or clear nail varnish is highly recommended)

3) 2cm x 25cm EL Tape

Another piece that can be cut to size is this straight piece of EL Tape that runs from the Knee Joint up to join the top half of the costume

Coming off the two-way splitter at the back of the costume:

4) EL SACRAL

This pair of pieces sits at the base of the spine and looks pretty awesome

The EL Tape is just 350 microns thick - that is 1/3rd of a millimetre!

Sticky back Velcro is supplied that is the exact width of the EL Tape - be careful putting it on as that glue is VERY sticky

You must sew the other part of the Velcro onto the costume making it very convenient to attach and remove

Of course, you don't need to use the Velcro, fix it any way you choose.

Its not complicated or fiddly.

The whole kit is ready to use - just plug and play!

We have some crazy glowing masks & glasses that go well with this kit - take a look!

A wide selection of other EL Tape, EL Wire, Sequencers, Drivers and helpful EL accessories are available from this store

Sam Flynn Tron - FULL Replica EL Panel Costume - Torso, Legs and Driver

Finally, we can get this full Tron Set running from a single portable Driver.

This Tron Full EL Panel Set in Light Blue (Tron Blue) is a combination of the Flynn Replica Torso Set and the Tron Leg Set

There are details of how we suggest the layout for replica below:

It goes on a bit, but that is to help you get it exactly right. It is all actually very easy to use and just clips together.

The guy on the right of the picture below has used the set to make a copy of the Sam Flynn costume (please note we do not supply the disc he is holding)

The girl on the left has created her own Tron inspired design with the same set. The design is completely flexible if you want to use it that way.

We suggest finding a comfortable garment to attach it to.

All these Tron Sets comes with sewable Velcro to go on the costume and sticky Velcro that goes on the back of the panel making it very easy to attach to any clothing

This is the full list of what is enclosed in this set and our suggested layout:

Torso Pieces

1) Two pieces of replica shaped EL Tape for the front of a Sam Flynn Costume - a Left and a Right

2) A single 1.5cm x 15cm EL Tape for the glowing mid line

3) A 14cm EL Identity Disc for the back of the costume

4) Two pieces of 2cm x 40cm Curved EL Tape for the back of a Tron Costume - It is curved to go round the ID Disc and over the shoulder

5) Two pieces of 1.5cm x 15cm EL Tape for the top of the arms of the Tron costume

6) 3 x 3 Way Splitters, a 2 x 2 Way Splitters and a 50cm long Extender to make it a simple 'plug and play' but also with plenty of room for the wire to stretch around the costume

Leg Pieces

1) Two pieces of replica shaped EL Tape for the boots of a Tron Costume - Sam Flynn, Rinzler or Quorra

2) Two pieces of shaped and angled EL Tape to go round the knees

3) Two pieces of sacral shaped EL Panel to go at the lower back

4) Two pieces of 2cm x 25cm EL Tape

5) A 2 Way Splitter, A 3 Way Splitter and 2 x 'Short, Medium and Long' Splitters

You will also get

1) 2 metres of Velcro - with sticky hoop and sewable loop to make it easy to attach the set to a costume and be removable so it can be washed.

2) A single Powerful 8x AAbattery (batteries not supplied) inverter to drive BOTH SETS

The whole kit is ready to use - just plug and play!

Dimensions of the products:

If you are making a costume, it is a good idea to plan it out properly.

The Torso Section

For this set, the driver/inverter is very powerful and comes with a separate power pack

So here are the dimensions of all the parts plus lengths of wire between them.

Feel free to message us if you have any questions.

THE POWER PACK:

Takes 8xAA batteries (not supplied) and is 12.7cm x 7.2cm x 1.9cm and has a 65cm thin power wire coming out of it that leads to the...

INVERTER / DRIVER:

The inverter is 6cm x 4cm x 4cm

It has the controls on it - Off, Flashing or On

It has a 55cm wire coming out of it that leads to the...

SPLITTER:

The Splitter is 40cm long in total and it is 20cm of wire which then splits into 3 separate strands which are all 20cm long - 2 of them then lead to...

Left and Right Flynn Replica EL Tapes:

The EL Tape is 30cm from top to tail with the stick and hoop that comes in near the shoulder adding another 8cm

The tape is just 350 microns thick - 1/3rd of a millimetre.

Sticky back Velcro is supplied that is the exact width of the EL Tape - be careful putting it on as the glue is VERY sticky

You will need to sew the other part of the Velcro onto the costume making it very convenient to attach and remove

You don't need to use the Velcro and can fix it any way you choose.

Mid-Line

Sam Flynn has a small line of light that runs down the middle of his chest. This is lit by the 1.5cm X15cm EL Tape provided. This tape can be easily cut to shape if you prefer it smaller

EL Identity Disc

This Large El Hoop is 14cm in diameter, there are two thin EL Tapes running in concentric circles and the inner diameter is just over 9cm across

2cm x 40cm Curved Outline

The EL Tape is curved so is 37 cm from top to tail - it has been designed to go on the back round the ID disc and curve over the shoulder

EL Tape for the Arms: 2pcs of 1.5cm x 15cm EL Tape, one for each arm

SPLITTERS:

This is how we recommend using the Splitters

A 2 Way Splitter coming straight from the Inverter - this divides the front and the back:

The First channel goes to a 3 Way Splitter to power the front of the costume - The left and right Flynn Tape plus the mid-line

The Second channel can be fitted with the Extender wire and this will allow it to reach to the back of the costume

A 3 Way Splitter attaches to this:

1 channel does the 1.5cm x 15cm left arm

2nd channel does the left 2cm x 40cm curved outline

The 3rd channel has another 3 Way Splitter on it

1st channel attaches to the ID Disc

2nd channel has the Right 2cm x 40cm curved outline

3rd channel does the 1.5cm x 15cm right arm

Depending on where you have the inverter, you may or may not need the extender wire

The Leg Section

1) Two pieces of replica shaped EL Tape for the boots of a Tron Costume - Sam Flynn, Rinzler or Quorra

2) Two pieces of shaped and angled EL Tape to go round the knees

3) Two pieces of sacral shaped EL Panel to go at the lower back

4) Two pieces of 2cm x 25cm EL Tape

5) A 2 Way Splitter, A 3 Way Splitter and 2 x 'Short, Medium and Long' Splitters

The whole kit is ready to use - just plug and play!

If you are making a costume, it is a good idea to plan it out properly.

For this set, the driver/inverter is very powerful and comes with a separate power pack

So here are the dimensions of all the parts plus lengths of wire between them.

DRIVER

The Torso and Leg set run off the same Driver

SPLITTER

The Splitter is 40cm long in total,

it is 20cm of wire which then splits into separate strands which are all 20cm long.

A 3 Way Splitter attaches to the Driver

One of these channels has a 2 Way Splitter attached that runs round the back to clip into the pair of EL Sacral pieces

The other two channels have a special '3 way Small Midi and Long' splitter attached to them that run down each leg

These SML splitters have:

one Short channel that plugs to the 25cm Tape.

Then the Middle channel plugs into the Knee Joint section

The Long channel goes down to the shin to plug into the Double Hoop

The three pieces of EL Tape that run down the leg are:

1) SHIN

This 15cm Double Hoop is designed to run from your shin to the ankle to give a great finishing touch to any Tron costume (these are also available for other parts of your Tron costume in our store

2) KNEE JOINT

Running up from the boot piece, this piece of EL Tape takes an angle round the knee, exactly as in the original costumes

This has been made to the largest size and will not fit everyone so it has been designed so you can just snip it down to the right size for you

That's right, it really is as easy as just cutting the unwanted part off either or both ends (sealing the cut with sellotape, glue or clear nail varnish is highly recommended)

3) 2cm x 25cm EL Tape

Another piece that can be cut to size is this straight piece of EL Tape that runs from the Knee Joint up to join the top half of the costume

Coming off the two-way splitter at the back of the costume:

4) EL SACRAL

This pair of pieces sits at the base of the spine and looks pretty awesome

The EL Tape is just 350 microns thick - that is 1/3rd of a millimetre!

Sticky back Velcro is supplied that is the exact width of the EL Tape - be careful putting it on as that glue is VERY sticky

You must sew the other part of the Velcro onto the costume making it very convenient to attach and remove

Of course, you don't need to use the Velcro, fix it any way you choose

Its not complicated or fiddly - I've just given all those details if you want to plan your costume before you buy the set - feel free to message us if you have any questions.

The whole kit is ready to use - just plug and play!

OR CONTACT US IF YOU WANT ADVICE PLANNING YOUR SET

We have some crazy glowing masks & glasses that go well with this kit - take a look!

Clu Replica EL Panel Front + Back + Driver

This listing is for:

1) One piece of Clu shaped EL Panel to run up one side of the chest

2) One 40cm angled piece of EL Tape to run up the other side of the chest

3) A 6cm EL Hoop to go on the shoulder at the top of the curved piece

4) 2 x Double hoops for the waist

5) A 14cm EL Tape Tron Identity Disc

6) A Powerful 8 x AA battery EL Driver or rechargeable 3000mAh Li-ion Driver.

7) 1 x 3-way splitter, a mini 2-way splitter, a mini 3-way splitter and a 50cm extender wire - these make the whole set a simple 'plug and play'

8) 1 metre of Velcro - with sticky hoop and sewable loop to make it easy to attach the set to a costume and have it removable

The whole kit is ready to use - just plug and play!

Dimensions of the products:

If you are making a costume, it is a good idea to plan it out properly.

For this set, the driver/inverter is very powerful and comes with a separate power pack

So here are the dimensions of all the parts plus lengths of wire between them.

Feel free to message us if you have any questions

THE POWER PACK*

Takes 8 x AA batteries (not supplied) and is 12.7cm x 7.02cm x 1.9cm and has a 19cm thin power wire coming out of it that leads to the driver.

DRIVER

The driver is 8cm x 5cm x 3.2cm and has the controls on it - Off, Flashing or On

It has a 55cm wire coming out of it that leads to the...

SPLITTER

The 3-way Splitter is 40cm long in total, it is 20cm of wire which then splits into 3 separate strands which are all 20cm long

2 of the 3 channels lead to the front of the costume, one to the Right and the other to the Left

Front Right

A mini 3-way splitter plugs into a 6cm EL Hoop, the 40cm Curved EL Panel and one of the Double Hoops

Sticky back Velcro is supplied that is the exact width of the EL Tape - be careful putting it on as that glue is VERY sticky

You must sew the other part of the Velcro onto the costume making it very convenient to attach and remove

Of course, you don't need to use the Velcro and can fix it any way you choose

Front Left

Here a mini 2-way splitter is plugged into the Clu shape EL Panel and the other Double Hoop

It is best to plug the 50cm extender into the 3rd channel off the main 3-way splitter which then leads to the...

EL Identity Disc

This Large El Hoop is 14cm in diameter, there are two thin EL Tapes running in concentric circles and the inner diameter is just over 9cm across

SPLITTERS

This is how we recommend using the splitters:

A 3-way splitter coming straight from the driver - one channel leads to a mini-3way splitter for the Front Right of the costume

- another channel leads to a mini 2-way splitter for the Front Left

- the last channel plugs into a 50cm extender and powers the ID disc at the back of the costume

* Instead of 8XAA battery pack this whole unit can be powered by a small rechargeable Li-ion battery

The 3000mAh battery is as powerful as 8xAA batteries but weighs only 172g and is 7.3cm x 5.6cm x 2.2cm

It comes with an Intelligent Charger with UK plug

Its not complicated or fiddly - I've just given all those details if you want to plan your costume before you buy the set - feel free to message me if you have any questions

The whole kit is ready to use - just plug and play!

OR CONTACT US IF YOU WANT ADVICE PLANNING YOUR SET

We have some crazy glowing masks & glasses that go well with this kit - take a look!

Siren Gem Replica EL Panel Set, Torso + Legs + Driver

This listing is for:

1) Four pieces of Angular EL Tape for the body of a Gem Costume

2) A single 1.5cm x 15cm EL Tape that can be easily snipped to length - for the glowing mid line

3) Two pieces of 2cm x 40cm Curved EL Tape for the back of a Tron Costume - It is curved to go round the ID Disc and over the shoulder

4) 1 x 14cm Tron Identity Disc, made of EL tape.

5) A Powerful 8 x AA battery EL Driver or rechargeable 3000mAh Li-ion Driver.

6) 1 x 4-way splitters, a 3-way splitter, a mini 3-way splitter and 2 x 50cm extender for the leg parts - these make the whole set a simple 'plug and play'

7) 1.5metres of Velcro - with sticky hoop and sewable loop to make it easy to attach the set to a costume and have it removable

This set is only available in Light Blue (Tron Blue)

The whole kit is ready to use - just plug and play!

Dimensions of the products:

If you are making a costume, it is a good idea to plan it out properly.

For this set, the driver/inverter is very powerful and comes with a separate power pack

So here are the dimensions of all the parts plus lengths of wire between them.

Feel free to message us if you have any questions

THE POWER PACK*

Takes 8 x AA batteries (not supplied) and is 12.7cm x 7.02cm x 1.9cm and has a 19cm thin power wire coming out of it that leads to the driver

DRIVER

The driver is 8cm x 5cm x 3.2cm

It has the controls on it - Off, Flashing or On

It has a 55cm wire coming out of it that leads to the...

SPLITTER

The 4- way Splitter is 40cm long in total,

it is 20cm of wire which then splits into 4 separate strands which are all 20cm long - 1 of them then lead to...

Gem Front

This part has its own mini-3way splitter attached to two of the 2cm x 40cm Curved EL Tape and the 1.5cm x 15cm mid line Piece

Sticky back Velcro is supplied that is the exact width of the EL Tape - be careful putting it on as that glue is VERY sticky

You must sew the other part of the Velcro onto the costume making it very convenient to attach and remove

Of course, you don't need to use the Velcro and can fix it any way you choose

Another channel, off the main 4-way splitter, goes to the back of the costume

Plug the other 3-way splitter into the 4-way splitter and those three channels go off too...

EL Identity Disc

This Large El Hoop is 14cm in diameter, there are two thin EL Tapes running in concentric circles and the inner diameter is just over 9cm across

and...

2cm x 40cm Curved Outline

The EL Tape is curved so is 37 cm from top to tail - it has been designed to go on the back round the ID disc and curve over the shoulder

The other two channels off the main 4-way splitter are for the leg pieces

a 50cm extender wire plugs into both of these to take the power too...

Gem Leg Pieces

Each leg has a 40 cm angled EL Tape to run down to the knee

SPLITTERS

This is how we recommend using the splitters

A 4-way splitter coming straight from the driver - for the front, the back and each leg

Depending on where you have the inverter, you may or may not need both extender wires

*Instead of 8 x AA battery pack this whole unit can be powered by a small rechargeable Li-ion battery

The 3000mAh battery is as powerful as 8 x AA batteries but weighs only 172g and is 7.3cm x 5.6cm x 2.2cm and comes with an Intelligent Charger

Its not complicated or fiddly - I've just given all those details if you want to plan your costume before you buy the set - feel free to message me if you have any questions

The whole kit is ready to use - just plug and play!

OR CONTACT US IF YOU WANT ADVICE PLANNING YOUR SET

We have some crazy glowing masks & glasses that go well with this kit - take a look!

Daft Punk Front EL Panels + Lapels + Driver

This set is what you need to replicate the glowing jackets used by Daft Punk

It has:

1) Two large EL Panels are just over 40cm long - replicas of the ones worn by Daft Punk.

These can either be worn both on the front, or one on the front and the other on the back

2) Zig-Zag Shapes for the lapels - these are 12cm long in total

3) Long 2 Way Splitter and 2 x Mini 2 Way Splitters

The Panels glow very brightly in Light Blue

4) The Driver that powers the two Panels is just 3cm x 4cm x 4cm and comes with an 8xAA Battery Box or a rechargeable Li-ion battery.

5) 1 metre of Velcro - sticky on one side and sewable on the other to help you attach the EL Tape and to a costume.

**RECHARGEABLE OPTION ONLY AVAILABLE TO UK - DUE TO EXPORT RESTRICTIONS**

The Driver is capable of powering more EL Tape or EL Wire if you want to add more parts from our online shop

We have some crazy glowing masks & glasses that go well with this kit - have a look!

A wide selection of other EL Tape, EL Wire, Sequencers, Drivers and helpful EL accessories are available from our online store.

EL Iron Man Body Set = EL Panel Arc Reactor + Hand Repulsors

Our Iron Man Sets supply you with 'plug and play' EL Panels, splitters and driver to help you build a glowing Iron Man Costume

With this kit you get:

1) 2 pieces of 3cm Diameter EL Panel for the Hand Repulsors

2) Plus a 10cm diameter round (or triangle shaped) white EL Panel for the Arc Reactor

3) Also a 2 x AA battery driver/inverter with switch to power the panels

4) And specialist 3 way splitter and 2 x 1.2m extenders to get power to the round panels down on the hands

EL Panels for the Hand Repulsor

The suggested setup is:

The Driver/Inverter is held on the body near the chest

A Three-way-splitter comes out and one channel goes off to the round panel acting as the Arc Reactor near the chest

The other two channels are longer and these have 1.2m extender wires attached to them to run down each arm to take power to the EL Panels for the Hand Repulsor

We have some crazy glowing masks & glasses that go well with this kit - take a look!

EL Iron Man Set = EL Tape Glowing Eyes + EL Panel Arc Reactor

The Iron Man Set is here to supply you with 'plug and play' EL Panels, splitters and driver to help you build a glowing Iron Man Costume

With this kit you get:

1) 2 pieces of 3cm x 5cm EL Panel for the Iron Man eyes in a choice of colours:

Light Blue, White, Red, Deep Blue and Pink

2) Plus a 10cm diameter round white EL Panel for the Arc Reactor

3) Also a 2 x AA battery driver/inverter with switch to power the panels

4) And 2 lots of 2 way splitters help the panels fit the costume

The suggested setup is:

The Driver/Inverter is held on the body near the chest

One two-way-splitter comes out and one channel goes off to the round panel acting as the Arc Reactor near the chest

The other channel has a second two-way splitter going off to the helmet to power the 3cm x 5cm EL Panels for the eyes

By having it on a second 2-way-splitter it makes it easier to unplug and remove the helmet - if it all runs off a 3-way-splitter, which it could, it would not be so easy to unplug the head mask

The kit does not include the mask or and its best to put a design over the glowing Arc Reactor - apart from that, the whole kit is ready to use - just plug and play!

EL Iron Man Set (Mark 6) = EL Tape Glowing Eyes + EL Panel Triangle

With this set you get:

2 pieces of 3cm x 5cm EL Panel for the Iron Man eyes in a choice of colours

A Triangle EL Panel for the Arc Reactor, 18cm on long side, 12cm on short sides and 9cm at deepest point

A 2 x AA battery powered EL Driver with trigger switch to power the EL panels

2 x 2-way splitters help the panels fit the costume.

The suggested setup is:

The Driver is held on the body near the chest

One 2-way-splitter comes out and one channel goes off to the triangle panel acting as the Arc Reactor near the chest

The other channel has a second two-way splitter going off to the helmet to power the 3cm x 5cm EL Panels for the eyes

These EL Panels are NOT SEE-THRU so you must design the eye piece to be above or below the actual eye

By having it on a second 2-way-splitter it makes it easier to unplug and remove the helmet - if it all runs off a 3-way-splitter, which it could, it would not be so easy to unplug the head mask

The kit does not include the mask or and its best to put a design over the glowing Arc Reactor - apart from that, the whole kit is ready to use - just plug and play!

A wide selection of other EL Tape, EL Wire, Sequencers, Drivers and helpful EL accessories are available from our online store.

- - - - - - - - - - - -

This EL Panel comes with a standard EL Wire connector so simply plugs into any EL driver.

Velcro - ? 2.00/m for attaching EL tape or EL panel to a fancy dress costume

This handy item is ideal for attaching EL Tape or EL Panels to clothing.

This Velcro has a sticky-back side that will stick firmly to the EL Tape or EL Panel.

The other part of the Velcro can be sewn onto the costume.

This makes it easy to remove the EL Panel for washing and general care.

The Velcro is 2cm Wide and 1 metre long

- - - - - - - - -

2cm Round Hoop - Flat EL Panel with Driver - Become Human Style

This 2cm Round EL Hoop is paper thin and can go flat against the skin.

This hoop is cleverly powered using a 5cm (2 inch) flat tape coming out of the hoop which can be coated in concealer paint to make the wire look invisible

You will need an EL Driver to power this EL Hoop and if you choose the 'Hoop and Driver' option we will supply a Mini EL Driver like this one:

You will also receive a 50cm extender wire to help you hide the driver, or if you are using other EL panels with the costume then you can attach it all to the same driver.

You may also be interested in our 7cm Triangle EL Panel:

https://elwirecraft.co.uk/product/7cm-triangle-detroit-become-human/

Black Widow Gauntlet Glove

This set is to help you recreate a glowing gauntlet glove from The Avengers Black Widow character

It is ideally attached to motorbike gloves

We also have a Black Widow Body and Leg Set

This Gauntlet Set consists of:

1) 2 x Light Blue (Tron Blue) EL Tapes 1.5cm x 20cm divided into four sections

These are to attach round the wrist

2) 2 x 10cm 1.5mm Light Blue (Tron Blue) EL Wires

These run up the back of the hand to form the 'Black Widow's Bite'

3) Mini EL Driver

This Driver takes a single AAA Battery and measures just 5cm x 3cm x 1.5cm
it can easily be hidden inside a motorbike glove

4) 4-way mini Splitter

This is the splitter you need to join all the wires and tape together into one Driver

5) 40cm of Velcro to help attach the EL Tape to the glove

It doesn't have to be attached this way, but it is fairly easy and our recommended way

This set is 'Plug and Play', you just need to attach it to your gloves

We have some crazy glowing masks & glasses that go well with this kit - take a look!

Avengers Black Widow Torso Set

This is the perfect set to help make an awesome Black Widow costume

It is part of a 3 part Full Black Widow Set that also includes her gauntlets and leg set
(but this one also looks great on its own)

With this set you get:

1) 1 pieces of 1.5 metres of high quality (3.2mm) Electroluminescent Wire.
This runs up the body, round behind the neck and then back down to the waist

2) 2 pieces of 50cm EL Wire for each of the arms

3) Trigger Driver so you can switch from 'glow mode' to 'incognito' using a switch in your sleeve

4) Speciality SLL (Short Long, Long) 3 Way Splitter to power the three EL Wires all over the body of the costume

5) 30 x Clear Hoops to make it easy to attach the EL Wire to the costume and also make it removable so you can put it through the washing machine

The EL Wire is in Light Blue (Tron Blue) but if you do want this set in a different colour please get in touch with us

To make it easier to design your outfit, below are the dimensions of the inverters and lengths of connecting wires - there is also tips on how to create your costume

DRIVER/INVERTER

The Power Pack takes 2 x AA batteries and is needed to make the EL Wire glow

The power pack/inverter is 8.5cm x 5cm x 2cm

It has an On/Off plunger switch that can run down the arm of the costume and be used to discreetly turn the glowing wire on and off

There is an 8cm wire coming out of it that leads to the...

SPLITTER

The Splitter has one short 10cm channel which is supposed to go to the 1.5m EL Wire

The two longer channels are 70cm and designed to reach up to the arms to light the 50cm EL Wires

EL WIRE
As explained above, the 1.5m EL Wire creates a great bodyline by starting at the waist, runs up the body and round the neck then returns to the waist

EL HOOPS

These make it easy to attach the EL Wire to a costume by sewing them on and then threading the EL Wire through the hoops. This also makes it easier to remove the EL Wire to wash the clothing

It is also possible to sew the EL Wire directly onto the costume

The whole kit is ready to use - just plug and play!

OR FEEL FREE TO CONTACT US IF YOU WANT HELP WITH YOUR EL PROJECT

We have some crazy glowing masks & glasses that go well with this kit - take a look!

Avengers Black Widow Torso and Leg Set

This is the perfect set to help make an awesome Black Widow costume

It is 2 parts of a 3 part Full Black Widow Set, which also includes her gauntlets.
(but this one also looks great on its own)

With this set you get:

1) 1 pieces of 1.5 metres of high quality (3.2mm) Electroluminescent Wire.
This runs up the body, round behind the neck and then back down to the waist

2) 2 pieces of 50cm EL Wire for each of the arms

3) 2 panels of EL Wire for each knee

4) Trigger Driver so you can switch from 'glow mode' to 'incognito' using a switch in your sleeve

5) A 2-way Mini Splitter leading to a Speciality SLL (Short Long, Long) 3 Way Splitter to power the three EL Wires all over the body of the costume and a Long 2-way Splitter to power the knee panels.

6) 30 x Clear Hoops to make it easy to attach the EL Wire to the costume and also make it removable so you can put it through the washing machine

The EL Wire is in Aqua (Tron Blue) but if you do want this set in a different colour please get in touch with us

To make it easier to design your outfit, below are the dimensions of the inverters and lengths of connecting wires - there is also tips on how to create your costume

DRIVER/INVERTER

The Power Pack takes 2 x AA batteries and is needed to make the EL Wire glow

The power pack/inverter is 8.5cm x 5cm x 2cm

It has an On/Off plunger switch that can run down the arm of the costume and be used to discreetly turn the glowing wire on and off

There is an 8cm wire coming out of it that leads to the...

SPLITTERS

The 3 way Splitter has one short 10cm channel which is supposed to go to the 1.5m EL Wire and the two longer channels are 70cm and designed to reach up to the arms to light the 50cm EL Wires

The mini 2 way splitter is 20cm long

EXTENDERS

Theses are 50cm long

EL WIRE
As explained above, the 1.5m EL Wire creates a great bodyline by starting at the waist, runs up the body and round the neck then returns to the waist

EL HOOPS

These make it easy to attach the EL Wire to a costume by sewing them on and then threading the EL Wire through the hoops. This also makes it easier to remove the EL Wire to wash the clothing

It is also possible to sew the EL Wire directly onto the costume

The whole kit is ready to use - just plug and play!

OR FEEL FREE TO CONTACT US IF YOU WANT HELP WITH YOUR EL PROJECT

We have some crazy glowing masks & glasses that go well with this kit - take a look!