Basic Tron Set = 2 x 1m of EL Wire + 2 x EL Tape Hoops + Driver

With this set you get:

1) 2 pieces of 1 metre high quality (3.2mm) Electroluminescent Wire

2) 2 x 6cm diameter EL Tape Hoops.

3) A decent 4 x AAA battery Driver/Inverter with on/off switch plus 4 modes including continuous ON, Strobe, Slow flash and Fast flash

4) 1 x 4 way splitter. The splitter lets you have 2 x 1 metre lengths of EL Wire and the 2 x 6cm hoops attached to one driver/inverter - This gives you greater control and flexibility in the designs of your Tron costume

5) 10cm of Velcro - sticky on one side and sewable on the other to help you attach the EL Hoops to a costume.

6) 10 clear plastic hoops - to sew on to your costume which you then feed the EL Wire through.

The EL Wire can be any combination of these colours:

Light Blue (Tron Blue), White, Red, Orange, Purple, Pink and Yellow

To make it easier to design your outfit, below are the dimensions of the inverters and lengths of connecting wires - there is also tips on how to create your costume

DRIVER/INVERTER

The Power Pack takes 4 x AAA batteries and has a built-in voltage inverter that 'inverts' the 6 Volts from the batteries up to the 100 Volts needed to make the EL Wire glow

The power pack/inverter is 8.5cm x 5cm x 2cm

It has an On/Off switch - plus a mode button for the 4 Modes: Continuous, Strobe, Fast flash and Slow flash

It has an 8cm wire coming out of it that leads to the...

SPLITTER

The Splitter is 40cm long in total,

it is 20cm of wire which then splits into 4 separate strands which are all 20cm long and lead to the...

EL WIRE

There is then another 20-25cm from the connector until the actual glowing start of EL Wire - then there is 2 X 1metres of gorgeous glowing wire!

These are long enough to run up the body and down the arm

EL HOOPS

The other part of the splitter runs to two 6cm diameter EL Hoops that make any Tron costume look amazing

Its not complicated or fiddly - I've just given all those details if you want to plan your costume before you buy the set

The whole kit is ready to use - just plug and play!

OR FEEL FREE TO CONTACT US IF YOU WANT HELP WITH YOUR EL PROJECT

We have some crazy glowing masks & glasses that go well with this kit - take a look!

LEG Pieces for Tron Replica Set

This Tron Leg Set contains:

1) Two pieces of replica shaped EL Tape for the boots of a Tron Costume - Sam Flynn, Rinzler or Quorra

2) Two pieces of shaped and angled EL Tape to go round the knees

3) Two pieces of sacral shaped EL Panel to go at the lower back

4) Two pieces of 2cm x 25cm EL Tape

5) A Powerful Driver with 8xAA Battery Box

6) A 2 Way Splitter, A 3 Way Splitter and 2 x 'Short, Medium and Long' Splitters

6) 1.5 metre of Velcro - with sticky hoop and sewable loop to make it easy to attach to a costume and have it removable for washing.

The Set is available in the following colours:

Orange or Light Blue

The whole kit is ready to use - just plug and play!

Dimensions of the products:

If you are making a costume, it is a good idea to plan it out properly. Feel free to email us with any questions you may have.

For this set, the Driver / Inverter is very powerful and comes with a separate power pack

So here are the dimensions of all the parts plus lengths of wire between them.

THE POWER PACK

Takes 8 x AA batteries (not supplied) and is 12.7cm x 7.2cm x 1.9cm

it has a 21cm thin power wire coming out of it that leads to the...

DRIVER

The Driver is 6cm x 4cm x 4cm

It has the controls on it - Off, Flashing or On

It has a 55cm wire coming out of it that leads to the...

SPLITTER

The Splitter is 40cm long in total,

it is 20cm of wire which then splits into separate strands which are all 20cm long.

A 3 Way Splitter attaches to the Driver

One of these channels has a 2 Way Splitter attached that runs round the back to clip into the pair of EL Sacral pieces

The other two channels have a special '3 Way Small Midi and Long' Splitter attached to them that run down each leg

These SML splitters have:

one Short channel that plugs to the 25cm Tape.

Then the Middle channel plugs into the Knee Joint section

The Long channel goes down to the Shin to plug into the Double Hoop

The three pieces of EL Tape that run down the leg are:

1) SHIN

This 15cm Double Hoop is designed to run from your shin to the ankle to give a great finishing touch to any Tron costume (these are also available for other parts of your Tron costume in our store

2) KNEE JOINT

Running up from the boot piece, this piece of EL Tape takes an angle round the knee, exactly as in the original costumes

This has been made to the largest size and will not fit everyone so it has been designed so you can just snip it down to the right size for you

That's right, it really is as easy as just cutting the unwanted part off either or both ends (sealing the cut with sellotape, glue or clear nail varnish is highly recommended)

3) 2cm x 25cm EL Tape

Another piece that can be cut to size is this straight piece of EL Tape that runs from the Knee Joint up to join the top half of the costume

Coming off the two-way splitter at the back of the costume:

4) EL SACRAL

This pair of pieces sits at the base of the spine and looks pretty awesome

The EL Tape is just 350 microns thick - that is 1/3rd of a millimetre!

Sticky back Velcro is supplied that is the exact width of the EL Tape - be careful putting it on as that glue is VERY sticky

You must sew the other part of the Velcro onto the costume making it very convenient to attach and remove

Of course, you don't need to use the Velcro, fix it any way you choose.

Its not complicated or fiddly.

The whole kit is ready to use - just plug and play!

We have some crazy glowing masks & glasses that go well with this kit - take a look!

A wide selection of other EL Tape, EL Wire, Sequencers, Drivers and helpful EL accessories are available from this store

Siren Gem Replica EL Panel Set, Torso + Legs + Driver

This listing is for:

1) Four pieces of Angular EL Tape for the body of a Gem Costume

2) A single 1.5cm x 15cm EL Tape that can be easily snipped to length - for the glowing mid line

3) Two pieces of 2cm x 40cm Curved EL Tape for the back of a Tron Costume - It is curved to go round the ID Disc and over the shoulder

4) 1 x 14cm Tron Identity Disc, made of EL tape.

5) A Powerful 8 x AA battery EL Driver or rechargeable 3000mAh Li-ion Driver.

6) 1 x 4-way splitters, a 3-way splitter, a mini 3-way splitter and 2 x 50cm extender for the leg parts - these make the whole set a simple 'plug and play'

7) 1.5metres of Velcro - with sticky hoop and sewable loop to make it easy to attach the set to a costume and have it removable

This set is only available in Light Blue (Tron Blue)

The whole kit is ready to use - just plug and play!

Dimensions of the products:

If you are making a costume, it is a good idea to plan it out properly.

For this set, the driver/inverter is very powerful and comes with a separate power pack

So here are the dimensions of all the parts plus lengths of wire between them.

Feel free to message us if you have any questions

THE POWER PACK*

Takes 8 x AA batteries (not supplied) and is 12.7cm x 7.02cm x 1.9cm and has a 19cm thin power wire coming out of it that leads to the driver

DRIVER

The driver is 8cm x 5cm x 3.2cm

It has the controls on it - Off, Flashing or On

It has a 55cm wire coming out of it that leads to the...

SPLITTER

The 4- way Splitter is 40cm long in total,

it is 20cm of wire which then splits into 4 separate strands which are all 20cm long - 1 of them then lead to...

Gem Front

This part has its own mini-3way splitter attached to two of the 2cm x 40cm Curved EL Tape and the 1.5cm x 15cm mid line Piece

Sticky back Velcro is supplied that is the exact width of the EL Tape - be careful putting it on as that glue is VERY sticky

You must sew the other part of the Velcro onto the costume making it very convenient to attach and remove

Of course, you don't need to use the Velcro and can fix it any way you choose

Another channel, off the main 4-way splitter, goes to the back of the costume

Plug the other 3-way splitter into the 4-way splitter and those three channels go off too...

EL Identity Disc

This Large El Hoop is 14cm in diameter, there are two thin EL Tapes running in concentric circles and the inner diameter is just over 9cm across

and...

2cm x 40cm Curved Outline

The EL Tape is curved so is 37 cm from top to tail - it has been designed to go on the back round the ID disc and curve over the shoulder

The other two channels off the main 4-way splitter are for the leg pieces

a 50cm extender wire plugs into both of these to take the power too...

Gem Leg Pieces

Each leg has a 40 cm angled EL Tape to run down to the knee

SPLITTERS

This is how we recommend using the splitters

A 4-way splitter coming straight from the driver - for the front, the back and each leg

Depending on where you have the inverter, you may or may not need both extender wires

*Instead of 8 x AA battery pack this whole unit can be powered by a small rechargeable Li-ion battery

The 3000mAh battery is as powerful as 8 x AA batteries but weighs only 172g and is 7.3cm x 5.6cm x 2.2cm and comes with an Intelligent Charger

Its not complicated or fiddly - I've just given all those details if you want to plan your costume before you buy the set - feel free to message me if you have any questions

The whole kit is ready to use - just plug and play!

OR CONTACT US IF YOU WANT ADVICE PLANNING YOUR SET

We have some crazy glowing masks & glasses that go well with this kit - take a look!