Adaptable Driver for 0 - 5m (Water Resistant)

This is a super adaptable EL Driver which will run up to 5meters of EL wire or 150squ cm of EL Tape or EL Panel

It DOES NOT have a flashing function - but comes with the option of an On/Off plunger switch. The switch will latch on when fully pressed down, press for a second time and the switch will latch off.

As explained in detail below, these Adaptable Drivers are very versatile with a whole selection of power supplies (Mains, Batteries, Direct 12V etc)

It has two integral screw fixing points on either side of it so it can be fastened down.

It has a water-tight seal all round it including where the wires come in and out of it. Attached in a sensible place it should withstand all types of weather

Its dimensions are: 28mm x 18mm x 24mm (L x W x H)

The screw fixing tabs stick out 6mm each on the 29mm side and could easily be cut off if space is vital. The driver weighs 25g.

EL Driver Options:

This EL Driver comes either with or without an On/Off switch.

Without a switch it will draw power whenever it is connected to a power source

Or It has a Trigger Switch on the end of a 1.2metre cable. For portable uses, this allows the unit to be held on the body while the switch runs down the sleeve to the hand. For other uses, it allows the driver to be mounted somewhere pretty far from the switch

This Driver has a range of power inputs that cover most potential uses, please choose one of these from the drop-down menu:

1) ONLY THE DRIVER

Maybe you have your own 12V 5.5mm/2.1mm input you want to use, perhaps you will be using one of the 2-way power splitters, or will you be cutting off the connector and using the bare wires?

Whatever your reason, this option gives you just the driver (as in the pic above) - without any external power connectors like the rest of these listed below...

2) Crocodile Clips

Perfect if you already have your own 12V battery to run this driver

3) 8xAA Battery Box

This 8xAA Battery Box will plug straight into the driver. It is fairly large (126mm X 72mm X 18mm) but will make this EL Driver portable

4) 3 x 18650 Rechargeable Battery Box

This 3 x 18650 Rechargeable Battery Box will plug straight into the driver. It is fairly large (63mm X 58mm X 30mm) and the leads for the output are 15cm long but will make this EL Driver portable.

5) Rechargeable Li-ion Battery

Much smaller and lighter than the Battery Box, these powerful Li-ion batteries come in a range of sizes

1800mAh (flat): 100g (10cm x 5.5cm x 0.8cm)

1800mAh: 100g (5cm x 3.3cm x 2.7cm)

3000mAh: 172g (7.3cm x 5.6cm x 2.2cm)

5000mAh: 265g (5.3cm x 5.8cm x 3.9cm)

All of these Li-ion Batteries come with an intelligent recharger

6) Mains Powered

This handy PSU can be used to make this EL Driver powered off of Mains Electricity (UK, US or Euro plugs are available)

7) Car Lighter Adaptor

This adaptor plugs into the car lighter socket. It is fused and ends with a 5.5mm/2.1mm jack plug so it can be used with any of our 12v Drivers or accessories

8) Self Stripping Wire Connectors (2)

This Driver is perfect for using when decorating your car with EL Wire.

An incredibly simple way to join the wires into your 12V loom is using these Self Stripping Wire Connectors (pack of 2)

9) 2 way Splitter for 12V Power Input (5.5mm)

If you're thinking of running two of these units off of one power source, then get yourself one of these splitters.

Please note this is a Splitter from the Battery to the Driver, so you would only need one Battery pack for 2 x Drivers.

Most people also use Splitters that come from the Driver to the EL Wire (so you only need 1 x Driver for many EL Wires) - you can get those types of EL WIRE SPLITTERS HERE

*If you want more than one of the power connector mentioned above for your EL Driver,

They can all be found in our Accessories section, or just click the description you want and be taken to its own page*

Remote Control

you can use this Remote Control Unit by connecting the Controller between the Power Source and the Driver

You can use several controllers with just one hand-held remote unit if you want to switch different drivers at once

The Remote Control Unit is not available in the drop down menu above - please click on the link to get the full details of this handy EL Accessory and add it to your basket

*All the EL wire we supply comes with a connector, so they plug straight into the driver*

- - - - - - - - - - - -

EL wire has loads of uses

This neon wire looks amazing when decorating the interior or exterior of cars, can be used inside and outside houses and can even be threaded into clothes and hats

It is a clichÃ© to say you are only limited by your imagination but with EL wire it is true!!!

If you have not seen it before it is like a really long glow stick that lasts around 5,000 hours

We're sure you will be amazed - feel free to message me with any questions.

Adaptable Driver for 5-15m (Flashing Option)

This handy item is a 12v driver with a variety of power inputs that will run between 5 and 15 meters of EL Wire.

The Driver has a switch on the side with 3 different positions Off - Flash - Continuous On.

As explained in detail below, these Adaptable Drivers are very versatile with a whole selection of power supplies (Mains, Batteries, Direct 12V etc)

The size of the Driver is: 5cm x 3.2cm x 2.8cm and weighs 61g.

Using splitters, this Driver can run as many strands as you like as long as the total is under 15 metres.

EL Driver Options:

We have found it is impossible to guess how you will be using the EL Wire, EL Tape and Drivers, so you will see on this website we have tried to give you as many choices as possible.

This driver is no exception as it has a range of power inputs that cover most potential uses, please choose one of these from the drop-down menu:

1) ONLY THE DRIVER

maybe you have your own 12V 5.5mm/2.1mm input you want to use, perhaps you will be using one of the 2-way power splitters?

Whatever your reason, this option gives you just the driver (as in the pic above) - without any external power connectors like the rest of these listed below...

2) Crocodile Clips

Perfect if you already have your own 12V battery to run this driver

3) 8xAA Battery Box

This 8xAA Battery Box will plug straight into the driver. It is fairly large (126mm X 72mm X 18mm) but will make this EL Driver portable

4) 3 x 18650 Rechargeable Battery Box

This 3 x 18650 Rechargeable Battery Box will plug straight into the driver. It is fairly large (63mm X 58mm X 30mm) and the leads for the output are 15cm long but will make this EL Driver portable.

5) Rechargeable Li-ion Battery

Much smaller and lighter than the Battery Box, these powerful Li-ion batteries come in a range of sizes

1800mAh (flat): 100g (10cm x 5.5cm x 0.8cm)

1800mAh: 100g (5cm x 3.3cm x 2.7cm)

3000mAh: 172g (7.3cm x 5.6cm x 2.2cm)

5000mAh: 265g (5.3cm x 5.8cm x 3.9cm)

All of these Li-ion Batteries come with an intelligent recharger

6) Mains Powered

This handy PSU can be used to make this EL Driver powered off of Mains Electricity (UK, US or Euro plugs are available)

7) Car Lighter Adaptor

This adaptor plugs into the car lighter socket. It is fused and ends with a 5.5mm/2.1mm jack plug so it can be used with any of our 12v Drivers or accessories

8) 2 way Splitter for 12V Power Input (5.5mm)

If you're thinking of running two of these units off of one power source, then get yourself one of these splitters.

Please note this is a Splitter from the Battery to the Driver, so you would only need one Battery pack for 2 x Drivers.

Most people also use Splitters that come from the Driver to the EL Wire (so you only need 1 x Driver for many EL Wires) - you can get those types of EL WIRE SPLITTERS HERE

*If you want more than one of the power connector mentioned above for your EL Driver,

They can all be found in our Accessories section, or just click the description you want and be taken to its own page*

Remote Control

you can use this Remote Control Unit by connecting the Controller between the Power Source and the Driver.

You can use several controllers with just one hand-held remote unit if you want to switch different drivers at once.

The Remote Control Unit is not available in the drop down menu above - please click on the link to get the full details of this handy EL Accessory and add it to your basket

*All the EL wire we supply comes with a connector, so they plug straight into the driver*

- - - - - - - - - - - -

EL wire has loads of uses

This neon wire looks amazing when decorating the interior or exterior of cars, can be used inside and outside houses and can even be threaded into clothes and hats

It is a cliché to say you are only limited by your imagination but with EL wire it is true!!!

If you have not seen it before it is like a really long glow stick that lasts over 5,000 hours

We're sure you will be amazed - feel free to message us with any questions.

1800mAh (Thin) Li-ion Battery

These batteries have been specially made for EL Wire Craft and are made with the highest quality Lithium Polymer technology.

While trying out different battery systems we found that many of them exaggerated the milliamp/Hour ratings. These batteries are within 10% of the rating at which they have been given.

They also feature overcharge protection.

They do not have their own on/off switch as we found this was unnecessary and just added another element that could fail.

We have these batteries in 4 different sizes with the following weights and dimensions:

1800mAh (Square): 125g (5.6cm x 3.8cm x 3.1cm)

3000mAh: 172g (7.3cm x 5.6cm x 2.2cm)

5000mAh: 265g (6.0cm x 5.8cm x 3.9cm)

15Ah: 725g (14.0cm x 6.5cm x 4.7cm)

SPECS:

Capacity: 1800mAh, 3000mAh or 5000mAh

Input power: DC 12.6V

Output: DC 12V

Over-charge / discharge protection: Yes

AC Mains Chargers are available with UK plugs.

These Li-ion batteries are best charged with dedicated Li-ion Intelligent Chargers

The 15Ah has an overcharge protection up to 15A so can take a larger current draw

Adaptable Driver for 5-15m (Trigger Switch)

This is a super adaptable EL Driver which will run from 5 to 15 metres of EL wire or 100 - 350squ cm of EL Tape or Panel

It DOES NOT have a flashing function - but has a Trigger Switch on the end of a 1.2metre cable.

For portable uses, this allows the unit to be held on the body while the switch runs down the sleeve to the hand. For other uses, it allows the driver to be mounted somewhere pretty far from the switch. The switch will latch on when fully pressed down, press for a second time and the switch will latch off.

It is similar to the Water Resistant 5-15m Adaptable Driver, but is boxed differently and not potted in resin making it lighter (and therefore more popular as a portable driver)

As explained in detail below, these Adaptable Drivers are very versatile with a whole selection of Power inputs (Mains, Batteries, Direct 12v etc)

Its dimensions are: 5.2cm x 3.2cm x 2.8cm (L x W x H) and weighs 61g.

EL Driver Options:

We have found it is impossible to guess how you will be using our EL Wire, EL Tape and Drivers, so you will see on this website we have tried to give you as many choices as possible.

This driver is no exceptions as it also has a range of power inputs that cover most potential uses, please choose one of these from the drop-down menu:

1) ONLY THE DRIVER

maybe you have your own 12V 5.5mm/2.1mm input you want to use, perhaps you will be using one of the 2-way power splitters, or will you be cutting off the connector and using the bare wires?

Whatever your reason, this option gives you just the driver (as in the pic above) - without any external power connectors like the rest of these listed below...

2) Crocodile Clips

Perfect if you already have your own 12V battery to run this driver

3) 8xAA Battery Box

This 8xAA Battery Box will plug straight into the driver. It is fairly large (126mm X 72mm X 18mm) but will make this EL Driver portable

4) 3 x 18650 Rechargeable Battery Box

This 3 x 18650 Rechargeable Battery Box will plug straight into the driver. It is fairly large (63mm X 58mm X 30mm) and the leads for the output are 15cm long but will make this EL Driver portable.

5) Rechargeable Li-ion Battery

Much smaller and lighter than the Battery Box, these powerful Li-ion batteries come in a range of sizes

1800mAh (flat): 100g (10cm x 5.5cm x 0.8cm)

1800mAh: 100g (5cm x 3.3cm x 2.7cm)

3000mAh: 172g (7.3cm x 5.6cm x 2.2cm)

5000mAh: 265g (5.3cm x 5.8cm x 3.9cm)

All of these Li-ion Batteries come with an intelligent recharger

6) Mains Powered

This handy PSU can be used to make this EL Driver powered off of Mains Electricity (UK, US or Euro plugs are available)

7) Car Lighter Adaptor

This adaptor plugs into the car lighter socket. It is fused and ends with a 5.5mm/2.1mm jack plug so it can be used with any of our 12v Drivers or accessories

8) 2 way Splitter for 12V Power Input (5.5mm)

If you're thinking of running two of these units off of one power source, then get yourself one of these splitters.

Please note this is a Splitter from the Battery to the Driver, so you would only need one Battery pack for 2 x Drivers

Most people also use Splitters that come from the Driver to the EL Wire (so you only need 1 x Driver for many EL Wires) - you can get those types of EL WIRE SPLITTERS HERE

*If you want more than one of the power connector mentioned above for your EL Driver,

They can all be found in our Accessories section, or just click the description you want and be taken to its own page*

Remote Control

You can use this Remote Control Unit by plugging the Controller between the Power Source and the Driver

You can use several controllers with just one hand-held remote unit if you want to switch several drivers at once

The Remote Control Unit is not available in the drop down menu above - please click on the link to get the full details of this handy EL Accessory and add it to your basket.

*All the EL wire we supply comes with a connector, so they plug straight into the driver*

- - - - - - - - - - - -

EL wire has loads of uses

This neon wire looks amazing when decorating the interior or exterior of cars, can be used inside and outside houses and can even be threaded into clothes and hats

It is a clichÃ© to say you are only limited by your imagination but with EL wire it is true!!!

If you have not seen it before it is like a really long glow stick that lasts around 5,000 hours

We're sure you will be amazed - feel free to message me with any questions

No Li-ion Battery

If you already have a Li-ion battery charger, this option is for you.

Our rechargeable Li-ion batteries have been specially made for EL Wire Craft and are made with the highest quality Lithium Polymer technology.

While trying out different battery systems, we found that many of them exaggerated the milliamp/Hour ratings. These batteries are within 10% of the rating at which they have been given.

They also feature overcharge protection.

They do not have their own on/off switch as we found this was unnecessary and just added another element that could fail.

We have these batteries in 4 different sizes:

1800mAh (Thin): 145g (10cm x 5.5cm x 1.1cm)

1800mAh (Square): 125g (5.6cm x 3.8cm x 3.1cm)

3000mAh: 172g (7.3cm x 5.6cm x 2.2cm)

5000mAh: 265g (6.0cm x 5.8cm x 3.9cm)

15Ah: 725g (14.0cm x 6.5cm x 4.7cm)

SPECS:

Capacity: 1800mAh, 3000mAh or 5000mAh

Input power: DC 12.6V

Output: DC 12V

Over-charge / discharge protection: Yes

No Li-ion Battery Charger

If you already have a dedicated intelligent Li-ion battery charger, this option is for you.

Our dedicated UK mains intelligent Li-ion battery chargers are available in 1A and 2A versions.

Specifications are:
1A
Input: 100 - 240V AC 0.8A 50/60hz.
Output: 12.6 V DC 1000mA

2A
Input: 100 - 240V AC 1A 50/60Hz
Output: 12.6V DC 2000mA

1800mAh (Square) Li-ion Battery

These batteries have been specially made for EL Wire Craft and are made with the highest quality Lithium Polymer technology.

While trying out different battery systems we found that many of them exaggerated the milliamp/Hour ratings. These batteries are within 10% of the rating at which they have been given.

They also feature overcharge protection.

They do not have their own on/off switch as we found this was unnecessary and just added another element that could fail.

We have these batteries in 4 different sizes with the following weights and dimensions:

1800mAh (Square): 145g (5.6cm x 3.8cm x 3.1cm)

3000mAh: 172g (7.3cm x 5.6cm x 2.2cm)

5000mAh: 265g (6.0cm x 5.8cm x 3.9cm)

15Ah: 725g (14.0cm x 6.5cm x 4.7cm)

SPECS:

Capacity: 1800mAh, 3000mAh or 5000mAh

Input power: DC 12.6V

Output: DC 12V

Over-charge / discharge protection: Yes

AC Mains Chargers are available with a UK plug.

These Li-ion batteries are best charged with dedicated Li-ion Intelligent Chargers.

3000mAh Li-ion Battery

These batteries have been specially made for EL Wire Craft and are made with the highest quality Lithium Polymer technology.

While trying out different battery systems we found that many of them exaggerated the milliamp/Hour ratings. These batteries are within 10% of the rating at which they have been given.

They also feature overcharge protection.

They do not have their own on/off switch as we found this was unnecessary and just added another element that could fail.

We have these batteries in 4 different sizes with the following weights and dimensions:

1800mAh (Thin): 145g (10cm x 5.5cm x 1.1cm)

1800mAh (Square): 145g (5.6cm x 3.8cm x 3.1cm)

3000mAh: 172g (7.3cm x 5.6cm x 2.2cm)

5000mAh: 265g (6.0cm x 5.8cm x 3.9cm)

15Ah: 725g (14.0cm x 6.5cm x 4.7cm)

SPECS:

Capacity: 1800mAh, 3000mAh or 5000mAh

Input power: DC 12.6V

Output: DC 12V

Over-charge / discharge protection: Yes

AC Mains Charger: UK Plug

These Li-ion batteries are best charged with dedicated Li-ion Intelligent Chargers.

CHASING Driver for 5 - 15m

This adaptable EL Driver only works for CHASING EL Wire

With this Driver you can adjust the speed of the chasing wire

It is a powerful driver and is suitable for 5m - 15m of standard Chasing EL Wire or 5m ULTRA Chasing EL Wire
It DOES NOT have an On /Off Switch and will switch on as soon as it is connected to a power source.

As explained in detail below, these Adaptable Drivers are very versatile with a whole selection of Power inputs (Mains, Batteries, Direct 12V etc)

Its dimensions are: 5cm x 4cm x 4cm (L x W x H) and weighs 80g.

Instructions:

1. Switch On, (to first position), ensuring that you have the EL Wire attached, as not having it attached when switching the Driver on can burn the Driver out.
2. The first position is ON and normal chasing speed.
3. Slide the switch to the last position and the Chasing EL Wire will move between speeding up and slowing down.
4. Watch the speed and when you see the speed that you want the EL Wire to chase at, move the switch back to the first position and it will lock the speed you want to use.

This Driver does have an On/Off Switch

EL Driver Options:

We have found it is impossible to guess how you will be using the EL Wire, EL Tape and Drivers, so you will see on this website we have tried to give you as many choices as possible.

This driver is no exception as it also has a range of power inputs that hopefully cover most uses:

1) ONLY THE DRIVER

Maybe you have your own 12V 5.5mm/2.1mm input you want to use, perhaps you will be using one of the 2-way power splitters?

Whatever your reason, this option gives you just the driver (as in the pic above) - without any external power connectors like the rest of these listed below...

2) Crocodile Clips

Perfect if you already have your own 12V battery to run this driver

3) 8xAA Battery Box

This 8xAA Battery Box will plug straight into the driver. It is fairly large (126mm X 72mm X 18mm) but will make this EL Driver portable

4) 3 x 18650 Rechargeable Battery Box

This 3 x 18650 Rechargeable Battery Box will plug straight into the driver. It is fairly large (63mm X 58mm X 30mm) and the leads for the output are 15cm long but will make this EL Driver portable.

5) Rechargeable Li-ion Battery

Much smaller and lighter than the Battery Box, these powerful Li-ion batteries come in a range of sizes

1800mAh (flat): 100g (10cm x 5.5cm x 0.8cm)

1800mAh: 100g (5cm x 3.3cm x 2.7cm)

3000mAh: 172g (7.3cm x 5.6cm x 2.2cm)

5000mAh: 265g (5.3cm x 5.8cm x 3.9cm)

All of these Li-ion Batteries come with an intelligent recharger

6) Mains Powered

This handy PSU can be used to make this EL Driver powered off of Mains Electricity (UK, US or Euro plugs are available)

7) Car Lighter Adaptor

This adaptor plugs into the car lighter socket. It is fused and ends with a 5.5mm/2.1mm jack plug so it can be used with any of our 12v Drivers or accessories

8) 2 way Splitter for 12V Power Input (5.5mm)

If you're thinking of running two of these units off of one power source, then get yourself one of these splitters.

Please note this is a Splitter from the Battery to the Driver, so you would only need one Battery pack for 2 x Drivers.

Most people also use Splitters that come from the Driver to the EL Wire (so you only need 1 x Driver for many EL Wires) - you can get those types of EL WIRE SPLITTERS HERE

*If you want more than one of the power connector mentioned above for your EL Driver,

They can all be found in our Accessories section, or just click the description you want and be taken to its own page*

1m extender for 12v

you can use this 1m Extender by connecting the extender between the Power Source and the Driver

The 1m Extender is not available in the drop down menu above - please click on the link to get the full details of this handy EL Accessory and add it to your basket

Remote Control

you can use this Remote Control Unit by connecting the Controller between the Power Source and the Driver

You can use several controllers with just one hand-held remote unit if you want to switch several drivers at once

The Remote Control Unit is not available in the drop down menu above - please click on the link to get the full details of this handy EL Accessory and add it to your basket

*All the EL wire we supply comes with a connector, so they plug straight into the driver*

- - - - - - - - - - - -

EL wire has loads of uses

It looks amazing when decorating the interior or exterior of cars, can be used inside and outside houses and can even be threaded into clothes and hats

It is a cliché to say you are only limited by your imagination but with EL wire it is true!!!

If you have not seen it before it is like a really long glow stick that lasts over 5,000 hours

We're sure you will be amazed - feel free to message us with any questions.

5000mAh Li-ion Battery

These batteries have been specially made for EL Wire Craft and are made with the highest quality Lithium Polymer technology.

While trying out different battery systems we found that many of them exaggerated the milliamp/Hour ratings. These batteries are within 10% of the rating at which they have been given.

They also feature overcharge protection.

They do not have their own on/off switch as we found this was unnecessary and just added another element that could fail.

We have these batteries in 4 different sizes with the following weights and dimensions:

1800mAh (Thin): 145g (10cm x 5.5cm x 1.1cm)

1800mAh (Square): 125g (5.6cm x 3.8cm x 3.1cm)

3000mAh: 172g (7.3cm x 5.6cm x 2.2cm)

5000mAh: 265g (6.0cm x 5.8cm x 3.9cm)

15Ah: 725g (14.0cm x 6.5cm x 4.7cm)

SPECS:

Capacity: 1800mAh, 3000mAh or 5000mAh

Input power: DC 12.6V

Output: DC 12V

Over-charge / discharge protection: Yes

AC Mains Chargers are available with a UK plug

These Li-ion batteries are best charged with dedicated Li-ion Intelligent Chargers.

Water Resistant 12v Driver for 5 - 15 metres of EL Wire or EL Tape.

Here we have a large and powerful EL Driver that is sealed within a waterproof casing - reducing the whistle while also making it water-resistant.

This is a 12v driver (with crocodile clips) which will run between 5 and 15 metres of EL neon glow wire or 150 - 400 square centimetres of EL Tape or EL Panel.

The driver DOES NOT have an on/off switch or a blinking function

But does have two integral screw fixing points on either side of it so it can be fastened down.

It has a water-tight seal all round it including where the wires come in and out of it. Attached in a sensible place it should withstand all types of weather.

Its dimensions are: 4cm x 3cm x 3cm (L x W x H)

The screw fixing tabs stick out 6mm each on the 4cm side and could easily be cut off

The wire from the crocodile clips is just under 1 metre long

Wire from inverter to EL wire connector is 17cm

** REMEMBER - The EL Driver will keep running while it is attached to a power source even if there is EL Wire or EL Tape attached to it or not**

*All the EL wire we supply comes with a connector, so they plug straight into the driver.*

The standard EL wire connector making it able to quickly switch between different coloured wire or add a splitter and have several strands of wire - simply clip it in and out the connector.

This driver can also run many strands and colours of EL wire as long as the total length of wire is between 5 and 15 meters.

Speaker wire can be used to extend the distance between the inverter and the start of the glowing EL wire.

FEEL FREE TO CONTACT US IF WE DO NOT HAVE YOUR REQUIRED LENGTH LISTED

- - - - - - - - - - - -

EL wire has loads of uses

It looks amazing when decorating the interior or exterior of cars, can be used inside and outside houses and can even be threaded into clothes and hats

It is a cliché to say you are only limited by your imagination but with EL wire it is true!!!

If you have not seen it before it is like a really long glow stick that lasts over 5,000 hours

We're sure you will be amazed - feel free to message us with any questions.

Water Resistant Driver for 5 - 15 metres of EL Wire with integral crocodile clips

Here we have a large and powerful EL Driver that is sealed within a waterproof casing - reducing the whistle while also making it water-resistant.

This is a 12v driver (with integral crocodile clips) which will run between 5 and 15 metres of EL neon glow wire or 50 - 300 square centimetres of EL Tape or EL Panel.

The driver DOES NOT have an on/off switch or a flashing function.

It does have two integral screw fixing points on either side of it so it can be fastened down.

It has a water-tight seal all round it including where the wires come in and out of it. Attached in a sensible place it should withstand all types of weather.

Its dimensions are: 4cm x 3.2cm x 3cm (L x W x H)

The screw fixing tabs stick out 7mm each on the 4cm side and could easily be cut off

The wire from the crocodile clips is just under 1/2 metre long

Wire from inverter to EL wire connector is 26cm

** REMEMBER - The EL Driver will keep running while it is attached to a power source even if there is EL Wire or EL Tape attached to it or not**

*All the EL wire we supply comes with a connector, so they plug straight into the driver.*

The standard EL wire connector making it able to quickly switch between different coloured wire or add a splitter and have several strands of wire - simply clip it in and out the connector.

This driver can also run many strands and colours of EL wire as long as the total length of wire is between 5 and 15 meters.

Speaker wire can be used to extend the distance between the inverter and the start of the glowing EL wire.

FEEL FREE TO CONTACT US IF WE DO NOT HAVE YOUR REQUIRED LENGTH LISTED

- - - - - - - - - - - -

EL wire has loads of uses

It looks amazing when decorating the interior or exterior of cars, can be used inside and outside houses and can even be threaded into clothes and hats

It is a cliché to say you are only limited by your imagination but with EL wire it is true!!!

If you have not seen it before it is like a really long glow stick that lasts over 5,000 hours

We're sure you will be amazed - feel free to message us with any questions.

Adaptable Driver for 10 - 40m (Flashing Option)

This adaptable EL Driver will run between 10 and 40 metres of EL Wire or 150 - 600 square cm (A4) of EL Panel or EL Tape.
It has a flashing option.

As explained in detail below, these Adaptable Drivers are very versatile with a whole selection of power supplies (Mains, Batteries, Direct 12V etc)

Its dimensions are: 8cm x 5cm x 3.2cm (L x W x H)

Weight: 130g

EL Driver Options:

We have found it is impossible to guess how you will be using the EL Wire, EL Tape and Drivers, so you will see on this website we have tried to give you as many choices as possible.

This driver is no exception as it also has a range of power inputs that hopefully cover most uses:

1) ONLY THE DRIVER

Maybe you have your own 12V 5.5mm/2.1mm input you want to use, perhaps you will be using one of the 2-way power splitters?

Whatever your reason, this option gives you just the driver (as in the pic above) - without any external power connectors like the rest of these listed below...

2) Crocodile Clips

Perfect if you already have your own 12V battery to run this driver

3) 8xAA Battery Box

This 8xAA Battery Box will plug straight into the driver. It is fairly large (126mm X 72mm X 18mm) but will make this EL Driver portable

4) 3 x 18650 Rechargeable Battery Box

This 3 x 18650 Rechargeable Battery Box will plug straight into the driver. It is fairly large (63mm X 58mm X 30mm) and the leads for the output are 15cm long but will make this EL Driver portable.

5) Rechargeable Li-ion Battery

Much smaller and lighter than the Battery Box, these powerful Li-ion batteries come in a range of sizes

1800mAh (flat): 100g (10cm x 5.5cm x 0.8cm)

1800mAh: 100g (5cm x 3.3cm x 2.7cm)

3000mAh: 172g (7.3cm x 5.6cm x 2.2cm)

5000mAh: 265g (5.3cm x 5.8cm x 3.9cm)

All of these Li-ion Batteries come with an intelligent charger as standard.

6) Mains Powered

This handy PSU can be used to make this EL Driver powered off of Mains Electricity (UK, US or Euro plugs are available)

7) Car Lighter Adaptor

This adaptor plugs into the car lighter socket. It is fused and ends with a 5.5mm/2.1mm jack plug so it can be used with any of our 12v Drivers or accessories

8) 2 way Splitter for 12V Power Input (5.5mm)

If you're thinking of running two of these units off of one power source, then get yourself one of these splitters.

Please note this is a Splitter from the Battery to the Driver, so you would only need one Battery pack for 2 x Drivers.

Most people also use Splitters that come from the Driver to the EL Wire (so you only need 1 x Driver for many EL Wires) - you can get those types of EL WIRE SPLITTERS HERE

*If you want more than one of the power connector mentioned above for your EL Driver,

They can all be found in our Accessories section, or just click the description you want and be taken to its own page*

Remote Control

you can use this Remote Control Unit by connecting the Controller between the Power Source and the Driver

You can use several controllers with just one hand-held remote unit if you want to switch several drivers at once

The Remote Control Unit is not available in the drop down menu above - please click on the link to get the full details of this handy EL Accessory and add it to your basket

*All the EL wire we supply comes with a connector, so they plug straight into the driver*

- - - - - - - - - - - -

EL wire has loads of uses

This neon wire looks amazing when decorating the interior or exterior of cars, can be used inside and outside houses and can even be threaded into clothes and hats

It is a cliché to say you are only limited by your imagination but with EL wire it is true!!!

If you have not seen it before it is like a really long glow stick that lasts over 5,000 hours

We're sure you will be amazed - feel free to message us with any questions.

Adaptable Driver for 10-40m (Trigger Switch)

This adaptable EL Driver will run between 10 and 40 meters of EL Wire and 150 - 600 square cm (A4) of EL Panel or EL Tape.
It DOES NOT have a flashing function - but has a Trigger Switch on the end of a 1.2metre cable.

As explained in detail below, these Adaptable Drivers are very versatile with a whole selection of power supplies (Mains, Batteries, Direct 12V etc)

Its dimensions are: 8cm x 5cm x 3.2cm (L x W x H) and weighs 130g.

EL Driver Options:

We have found it is impossible to guess how you will be using the EL Wire, EL Tape and Drivers, so you will see on this website we have tried to give you as many choices as possible.

This driver is no exception as it also has a range of power inputs that hopefully cover most uses:

1) ONLY THE DRIVER

Maybe you have your own 12V 5.5mm/2.1mm input you want to use, perhaps you will be using one of the 2-way power splitters?

Whatever your reason, this option gives you just the driver (as in the pic above) - without any external power connectors like the rest of these listed below...

2) Crocodile Clips

Perfect if you already have your own 12V battery to run this driver

3) 8xAA Battery Box

This 8xAA Battery Box will plug straight into the driver. It is fairly large (126mm X 72mm X 18mm) but will make this EL Driver portable

4) 3 x 18650 Rechargeable Battery Box

This 3 x 18650 Rechargeable Battery Box will plug straight into the driver. It is fairly large (63mm X 58mm X 30mm) and the leads for the output are 15cm long but will make this EL Driver portable.

5) Rechargeable Li-ion Battery

Much smaller and lighter than the Battery Box, these powerful Li-ion batteries come in a range of sizes

1800mAh (thin): 125g (10cm x 5.5cm x 0.8cm)

1800mAh (square): 125g (5cm x 3.3cm x 2.7cm)

3000mAh: 172g (7.3cm x 5.6cm x 2.2cm)

5000mAh: 250g (5.3cm x 5.8cm x 3.9cm)

All of these Li-ion Batteries come with an intelligent recharger

6) Mains Powered

This handy PSU can be used to make this EL Driver powered off of Mains Electricity (UK, US or Euro plugs are available)

7) Car Lighter Adaptor

This adaptor plugs into the car lighter socket. It is fused and ends with a 5.5mm/2.1mm jack plug so it can be used with any of our 12v Drivers or accessories

8) 2 way Splitter for 12V Power Input (5.5mm)

If you're thinking of running two of these units off of one power source, then get yourself one of these splitters.

Please note this is a Splitter from the Battery to the Driver, so you would only need one Battery pack for 2 x Drivers.

Most people also use Splitters that come from the Driver to the EL Wire (so you only need 1 x Driver for many EL Wires) - you can get those types of EL WIRE SPLITTERS HERE

*If you want more than one of the power connector mentioned above for your EL Driver,

They can all be found in our Accessories section, or just click the description you want and be taken to its own page*

Remote Control

You can use this Remote Control Unit by connecting the Controller between the Power Source and the Driver

You can use several controllers with just one hand-held remote unit if you want to switch several drivers at once.

The Remote Control Unit is not available in the drop down menu above - please click on the link to get the full details of this handy EL Accessory and add it to your basket

*All the EL wire we supply comes with a connector, so they plug straight into the driver*

- - - - - - - - - - - -

EL wire has loads of uses

This neon wire looks amazing when decorating the interior or exterior of cars, can be used inside and outside houses and can even be threaded into clothes and hats

It is a cliché to say you are only limited by your imagination but with EL wire it is true!!!

If you have not seen it before it is like a really long glow stick that lasts over 5,000 hours

We're sure you will be amazed - feel free to message us with any questions.

Adaptable Driver for 20 - 60m

This handy item is an adaptable driver which will run between 20 and 60 metres of EL Wire.

Running any less wire than 20m will reduce the lifespan of the wire and strain this driver as it is being overpowered.

The Driver has a switch on the back for either continuous ON or Flashing

The size of the Driver is: 12cm x 6.5cm x 3cm and weighs 222g.

This is a very powerful inverter that not only runs very long lengths of EL Wire but does so much brighter than most other drivers!

Using splitters it can run as many strands as you like as long as the total is under 60 metres

1) ONLY THE DRIVER

maybe you have your own 12V 5.5mm/2.1mm input you want to use, perhaps you will be using one of the 2-way power splitters?

Whatever your reason, this option gives you just the driver (as in the pic above) - without any external power supply like the rest of these listed below...

2) Crocodile Clips

Perfect if you already have your own 12V battery to run this driver

3) 8xAA Battery Box

This 8xAA Battery Box will plug straight into the driver. It is fairly large (126mm X 72mm X 18mm) but will make this EL Driver portable

4) 3 x 18650 Rechargeable Battery Box

This 3 x 18650 Rechargeable Battery Box will plug straight into the driver. It is fairly large (63mm X 58mm X 30mm) and the leads for the output are 15cm long but will make this EL Driver portable.

5) Rechargeable Li-ion Battery

Much smaller and lighter than the Battery Box, these powerful Li-ion batteries come in a range of sizes

1800mAh (flat): 100g (10cm x 5.5cm x 0.8cm)

1800mAh: 100g (5cm x 3.3cm x 2.7cm)

3000mAh: 172g (7.3cm x 5.6cm x 2.2cm)

5000mAh: 265g (5.3cm x 5.8cm x 3.9cm)

All of these Li-ion Batteries come with an intelligent recharger

6) Mains Powered

This handy PSU can be used to make this EL Driver powered off of Mains Electricity (UK, US or Euro plugs are available)

7) Car Lighter Adaptor

This adaptor plugs into the car lighter socket. It is fused and ends with a 5.5mm/2.1mm jack plug so it can be used with any of our 12v Drivers or accessories

8) 2 way Splitter for 12V Power Input (5.5mm)

If you're thinking of running two of these units off of one power source, then get yourself one of these splitters.

Please note this is a Splitter from the Battery to the Driver, so you would only need one Battery pack for 2 x Drivers.

Most people also use Splitters that come from the Driver to the EL Wire (so you only need 1 x Driver for many EL Wires) - you can get those types of EL WIRE SPLITTERS HERE

*If you want more than one of the power connector mentioned above for your EL Driver,

They can all be found in our Accessories section, or just click the description you want and be taken to its own page*

Remote Control

you can use this Remote Control Unit by connecting the Controller between the Power Source and the Driver

You can use several controllers with just one hand-held remote unit if you want to switch different drivers at once

The Remote Control Unit is not available in the drop down menu above - please click on the link to get the full details of this handy EL Accessory and add it to your basket

*All the EL wire we supply comes with a connector, so they plug straight into the driver*

- - - - - - - - - - - -

EL wire has loads of uses

It looks amazing when decorating the interior or exterior of cars, can be used inside and outside houses and can even be threaded into clothes and hats

It is a cliché to say you are only limited by your imagination but with EL wire it is true!!!

If you have not seen it before it is like a really long glow-stick that lasts over 5,000 hours

We're sure you will be amazed - feel free to message us with any questions.

Portable Mini Driver for 1 metre EL Wire or 50sq cm EL Tapes/Panels

Here we have a really handy small portable EL Driver that takes 1 x AAA battery (battery not supplied).

It's dimensions are: 5.1cm x 2.9cm x 1.5cm and it can power up to 2 metres of EL Wire but it is ideal when running 1 metre or under of EL Wire.

When it is used to drive more than 1 metre of EL Wire, the whistle of the inverter becomes audible.

(This is important to consider if you are using it in a hat or mask)

The driver has a switch with 3 settings: On / Off / Flash

This EL Driver has an 8cm long output wire with a standard EL wire connector on the end

Use this to connector plug in EL Wire or a Splitter

*All the EL wire we supply comes with a connector, so they plug straight into the driver*

**EL Drivers contain an inverter that switches the current from DC to AC and increases the voltage - for this reason EL Drivers are often called EL Inverters - they are the same thing**

Using a splitter, this driver can run many strands and colours of EL wire as long as the total length of wire is 2 meters or under

FEEL FREE TO CONTACT US IF WE DO NOT HAVE YOUR REQUIRED LENGTH LISTED

A wide selection of other EL Tape, EL Wire, Sequencers, Drivers and helpful EL accessories are available from our online store.

- - - - - - - - - - - -

EL wire has loads of uses.

It looks amazing when decorating the interior or exterior of cars, can be used inside and outside houses and can even be threaded into clothes and hats.

The EL wire can be cut into smaller lengths and attached to another driver.

Or with some care, the EL wire can be attached to speaker wire to make patterns or extend the wire over gaps where it isn't needed.

It is a cliché to say you are only limited by your imagination but with EL wire it is true!!!

If you have not seen it before it is like a really long glow stick that lasts over 5,000 hours.

We're sure you will be amazed - feel free to message us with any questions.